- 您现在的位置：买卖IC网 > PDF目录1793 > FSD176MRTUDTU (Fairchild Semiconductor)IC OFF-LINE SWITCH PWM TO220-6 PDF资料下载
参数资料
| 型号： | FSD176MRTUDTU |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 11/17页 |
| 文件大小： | 0K |
| 描述： | IC OFF-LINE SWITCH PWM TO220-6 |
| 标准包装： | 50 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 61kHz ~ 73kHz |
| 输入电压： | 13 V ~ 26 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 90W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | * |
| 供应商设备封装： | * |
| 包装： | * |
4.3. Output-Short Protection (OSP) : If the output is
shorted, steep current with extremely high di/dt can
flow through the SenseFET during the minimum turn-
on time. Such a steep current brings high-voltage
stress on the drain of the SenseFET when turned off.
To protect the device from this abnormal condition,
OSP is included. It is comprised of detecting V FB and
SenseFET turn-on time. When the V FB is higher than
2.0 V and the SenseFET turn-on time is lower than
1.0 μ s, the FSD176MRT recognizes this condition as
an abnormal error and shuts down PWM switching
until V CC reaches V START again. An abnormal condition
output short is shown in Figure 22.
Figure 22. Output-Short Protection
5. Soft Burst-Mode Operation : To minimize power
dissipation in Standby Mode, the FSD176MRT enters
Burst-Mode operation. As the load decreases, the
feedback voltage decreases. The device automatically
enters Burst Mode when the feedback voltage drops
below V BURL (300 mV), as shown in Figure 23. At this
point, switching stops and the output voltages start to
drop at a rate dependent on standby current load. This
causes the feedback voltage to rise. Once it passes
V BURH (450 mV), switching resumes. The feedback
voltage then falls and the process repeats. Burst Mode
alternately enables and disables switching of the
SenseFET, reducing switching loss in Standby Mode.
4.4 Over-Voltage Protection (OVP):
If the
secondary-side feedback circuit malfunctions or a
solder defect causes an opening in the feedback path,
the current through the opto-coupler transistor
becomes almost zero. Then V FB climbs up in a similar
manner to the overload situation, forcing the preset
maximum current to be supplied to the SMPS until the
overload protection is triggered. Because more energy
than required is provided to the output, the output
voltage may exceed the rated voltage before the
overload protection is triggered, resulting in the
breakdown of the devices in the secondary side. To
prevent this situation, an OVP circuit is employed. In
general, the V CC is proportional to the output voltage
and the FSD176MRT uses V CC instead of directly
monitoring the output voltage. If V CC exceeds 24.5 V,
an OVP circuit is triggered, resulting in the termination
Figure 23. Burst-Mode Operation
6. Random Frequency Fluctuation (RFF) : Fluctuating
switching frequency of an SMPS can reduce EMI by
spreading the energy over a wide frequency range. The
amount of EMI reduction is directly related to the
switching frequency variation, which is limited internally.
The switching frequency is determined randomly by
external feedback voltage and an internal free-running
oscillator at every switching instant. This random
frequency fluctuation scatters the EMI noise around
typical switching frequency (67 kHz) effectively and can
reduce the cost of the input filter included to meet the
EMI requirements (e.g. EN55022).
of the switching operation. To avoid undesired
activation of OVP during normal operation, V CC should
be designed to be below 24.5 V.
4.5 Thermal Shutdown (TSD) : The SenseFET and
the control IC on a die in one package makes it easier
for the control IC to detect the over temperature of the
SenseFET. If the temperature exceeds ~140 ° C, the
thermal shutdown is triggered and stops operation.
The FSD176MRT operates in auto-restart mode until
the temperature decreases to around 75 ° C, when
normal operation resumes.
Figure 24. Random Frequency Fluctuation
? 2011 Fairchild Semiconductor Corporation
FSD176MRT ? Rev. 1.0.1
11
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSDL321 | IC SWIT PWM GREEN CM OVP HV 8DIP |
| FSDM0565RBIWDTU | IC SWIT PWM GREEN CM HV I2PAK |
| FSDM0565RELDTU | IC PWM/SENSEFET 650V TO-220F-6 |
| FSDM07652RBWDTU | IC SWIT PWM GREEN CM HV TO220F |
| FSDM1265RBWDTU | IC SWIT PWM GREEN CM HV TO220F |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSD-1A | 制造商:OPTIFUSE 功能描述: |
| FSD1V | 功能描述:螺丝刀、螺母起子和套筒扳手 Four-in-One Screwdriver, Carded RoHS:否 制造商:Wiha 产品: 类型:Wiha Magic Ring Ball End Hex Keys 大小: |
| FSD200 | 功能描述:电源开关 IC - 配电 SMPS Power Switch RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSD200B | 功能描述:电源开关 IC - 配电 SMPS Power Switch for Chargers RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSD200BM | 功能描述:电源开关 IC - 配电 POWER_CONVERSION RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。