- 您现在的位置：买卖IC网 > PDF目录19587 > FSGM0465RUDTU (Fairchild Semiconductor)IC PWM/SENSEFET SMPS TO-220F-6U PDF资料下载
参数资料
| 型号： | FSGM0465RUDTU |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 11/19页 |
| 文件大小： | 0K |
| 描述： | IC PWM/SENSEFET SMPS TO-220F-6U |
| 标准包装： | 400 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 60kHz ~ 72kHz |
| 输入电压： | 13 V ~ 23 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 70W |
| 工作温度： | -40°C ~ 125°C |
| 封装/外壳： | TO-220FL |
| 供应商设备封装： | TO-220F-6L（U 型） |
| 包装： | 管件 |
4. Protection Circuits : The FSGM0465R has several
self-protective functions, such as Overload Protection
(OLP), Abnormal Over-Current Protection (AOCP),
Output-Short Protection (OSP), Over-Voltage Protection
(OVP), and Thermal Shutdown (TSD). All the
protections are implemented as auto-restart. Once the
increasing until it reaches 6.0V, when the switching
operation is terminated, as shown in Figure 20. The
delay time for shutdown is the time required to charge
C FB from 2.4V to 6.0V with 3.3 μ A. A 25 ~ 50ms delay
is typical for most applications. This protection is
implemented in auto-restart mode.
When V CC falls to the Under-Voltage Lockout (UVLO)
fault condition is detected, switching is terminated and
the SenseFET remains off. This causes V CC to fall.
B B
stop voltage of 7.5V, the protection is reset and the
startup circuit charges the V CC capacitor. When V CC
reaches the start voltage of 12.0V, the FSGM0465R
resumes normal operation. If the fault condition is not
removed, the SenseFET remains off and V CC drops to
stop voltage again. In this manner, the auto-restart can
alternately enable and disable the switching of the
power SenseFET until the fault condition is eliminated.
Because these protection circuits are fully integrated
into the IC without external components, the reliability is
improved without increasing cost.
Figure 20. Overload Protection
4.2 Abnormal Over-Current Protection (AOCP) :
When the secondary rectifier
diodes or the
transformer pins are shorted, a steep current with
extremely high di/dt can flow through the SenseFET
during the minimum turn-on time. Even though the
FSGM0465R has overload protection, it is not enough
to protect the FSGM0465R in that abnormal case;
since severe current stress is imposed on the
SenseFET until OLP is triggered. The FSGM0465R
internal AOCP circuit is shown in Figure 21. When the
gate turn-on signal is applied to the power SenseFET,
the AOCP block is enabled and monitors the current
through the sensing resistor. The voltage across the
resistor is compared with a preset AOCP level. If the
sensing resistor voltage is greater than the AOCP
level, the set signal is applied to the S - R latch,
resulting in the shutdown of the SMPS.
Figure 19. Auto-Restart Protection Waveforms
4.1 Overload Protection (OLP) : Overload is defined
as the load current exceeding its normal level due to
an unexpected abnormal event. In this situation, the
protection circuit should trigger to protect the SMPS.
However, even when the SMPS is in normal
operation, the overload protection circuit can be
triggered during the load transition. To avoid this
undesired operation, the overload protection circuit is
designed to trigger only after a specified time to
determine whether it is a transient situation or a true
overload situation. Because of the pulse-by-pulse
current limit capability, the maximum peak current
through the SenseFET is limited and, therefore, the
maximum input power is restricted with a given input
voltage. If the output consumes more than this
maximum power, the output voltage (V OUT ) decreases
below the set voltage. This reduces the current
through the opto-coupler LED, which also reduces the
opto-coupler transistor current, thus increasing the
feedback voltage (V FB ). If V FB exceeds 2.4V, D1 is
blocked and the 3.3 μ A current source starts to charge
C FB slowly up . In this condition, V FB continues
? 2009 Fairchild Semiconductor Corporation
FSGM0465R ? Rev. 1.0.3
11
Figure 21. Abnormal Over-Current Protection
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| 172-037-212R911 | CONN DB37 FMALE VERT BRDLOCK SLD |
| ACB25DHAT | CONN EDGECARD 50POS R/A .050 DIP |
| TAP155M050BRS | CAP TANT 1.5UF 50V 20% RADIAL |
| EPM7032STC44-6 | IC MAX 7000 CPLD 32 44-TQFP |
| MIC5255-2.8BML TR | IC REG LDO 2.8V .15A 6-MLF |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSGM0465RWDTU | 功能描述:电流型 PWM 控制器 FPS RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| FSGM0565R | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green-Mode Fairchild Power Switch (FPS?) |
| FSGM0565RB | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green-Mode Fairchild Power Switch |
| FSGM0565RBLDTU | 功能描述:电源开关 IC - 配电 SMPS PWR SW, 5A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSGM0565RBUDTU | 功能描述:电源开关 IC - 配电 SMPS PWR SW, 5A 650V RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
发布紧急采购，3分钟左右您将得到回复。