- 您现在的位置：买卖IC网 > PDF目录68995 > FSL126MR (FAIRCHILD SEMICONDUCTOR CORP) 8 A SWITCHING CONTROLLER, 73 kHz SWITCHING FREQ-MAX, PDIP8 PDF资料下载
参数资料
| 型号： | FSL126MR |
| 厂商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分类： | 稳压器 |
| 英文描述： | 8 A SWITCHING CONTROLLER, 73 kHz SWITCHING FREQ-MAX, PDIP8 |
| 封装： | MS-001BA, DIP-8 |
| 文件页数： | 2/13页 |
| 文件大小： | 892K |
| 代理商： | FSL126MR |
2010 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FSL126MR Rev. 1.0.0
10
FSL126M
R
—
Green
M
ode
Fairchild
Power
Swit
ch
(
F
PS)
Figure 17. Auto-Restart Protection Waveforms
Overload Protection (OLP)
Overload is defined as the load current exceeding a
pre-set level due to an unexpected event. In this
situation, the protection circuit should be activated to
protect the SMPS. However, even when the SMPS is
operating normally, the overload protection (OLP) circuit
can be activated during the load transition or startup. To
avoid this undesired operation, the OLP circuit is
designed to be activated after a specified time to
determine whether it is a transient situation or a true
overload situation.
In conjunction with the IPK current limit pin (if used), the
current-mode feedback path limits the current in the
SenseFET when the maximum PWM duty cycle is
attained. If the output consumes more than this
maximum power, the output voltage (VO) decreases
below its rating voltage. This reduces the current
through the opto-coupler LED, which also reduces the
opto-coupler transistor current, thus increasing the
feedback voltage (VFB). If VFB exceeds 2.4V, the
feedback input diode is blocked and the 5A current
source (IDELAY) starts to charge CFB slowly up to VCC. In
this condition, VFB increases until it reaches 6V, when
the switching operation is terminated, as shown in
Figure 18. The shutdown delay is the time required to
charge CFB from 2.4V to 6V with 5A current source.
Figure 18. Overload Protection (OLP)
Abnormal Over-Current Protection (AOCP)
When the secondary rectifier diodes or the transformer
pin are shorted, a steep current with extremely high
di/dt can flow through the SenseFET during the LEB
time. Even though the FPS has OLP (Overload
Protection), it is not enough to protect the FPS in that
abnormal case, since severe current stress is imposed
on the SenseFET until OLP triggers. The FPS includes
the internal AOCP (Abnormal Over-Current Protection)
circuit shown in Figure 19. When the gate turn-on signal
is applied to the power SenseFET, the AOCP block is
enabled and monitors the current through the sensing
resistor. The voltage across the resistor is compared
with a preset AOCP level. If the sensing resistor voltage
is greater than the AOCP level, the set signal is applied
to the latch, resulting in the shutdown of the SMPS.
Figure 19.Abnormal Over-Current Protection
Thermal Shutdown (TSD)
The SenseFET and the control IC are integrated,
making it easier to detect the temperature of the
SenseFET.
When
the
temperature
exceeds
approximately 137°C, thermal shutdown is activated.
Over-Voltage Protection (OVP)
In the event of a malfunction in the secondary-side
feedback circuit or an open feedback loop caused by a
soldering defect, the current through the opto-coupler
transistor becomes almost zero. Then, VFB climbs up in
a similar manner to the overload situation, forcing the
preset maximum current to be supplied to the SMPS
until the overload protection is activated. Because
excess energy is provided to the output, the output
voltage may exceed the rated voltage before the
overload protection is activated, resulting in the
breakdown of the devices in the secondary side. To
prevent this situation, an over-voltage protection (OVP)
circuit is employed. In general, VCC is proportional to the
output voltage and the FPS uses VCC instead of directly
monitoring the output voltage. If VCC exceeds 24V, OVP
circuit is activated, resulting in termination of the
switching operation. To avoid undesired activation of
OVP during normal operation, VCC should be designed
to be below 24V.
相关PDF资料 |
PDF描述 |
|---|---|
| FSL136HR | 2.41 A SWITCHING CONTROLLER, 110 kHz SWITCHING FREQ-MAX, PDIP8 |
| FSL136MR | SWITCHING CONTROLLER, PDIP8 |
| FSQ0565RQ | 3.36 A SWITCHING CONTROLLER, 75.8 kHz SWITCHING FREQ-MAX, ZFM6 |
| FSQ0565RS | 2.5 A SWITCHING CONTROLLER, 75.8 kHz SWITCHING FREQ-MAX, ZFM6 |
| FSQ0765RS | SWITCHING CONTROLLER, ZFM6 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSL126MRT | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green-Mode Fairchild Power Switch (FPSa?￠) |
| FSL126MRTWDTU | 功能描述:电源开关 IC - 配电 6.2Ohms 1mA 50W RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSL127H | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch |
| FSL127HNY | 功能描述:电源开关 IC - POE / LAN Green Mode Power Switch RoHS:否 制造商:Fairchild Semiconductor 开关数量:Single 开关配置:SPST 开启电阻（最大值）:7.3 Ohms 串话: 带宽: 开启时间（最大值）:13 ns 关闭时间（最大值）:20 ns 切换电压（最大）: 工作电源电压:8 V to 26 V 最大工作温度:+ 125 C 安装风格:Through Hole 封装 / 箱体:TO-220F-6 |
| FSL127HNYI | 制造商:Fairchild Semiconductor Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。