参数资料
| 型号： | FSL206MRBN |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 11/14页 |
| 文件大小： | 0K |
| 描述： | IC FPS POWER SWITCH 8-MDIP |
| 标准包装： | 1 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 61kHz ~ 73kHz |
| 输入电压： | 8 V ~ 26 V |
| 输出电压： | 650V |
| 功率（瓦特）： | 12W |
| 工作温度： | -40°C ~ 115°C |
| 封装/外壳： | 8-DIP（0.300"，7.62mm） |
| 供应商设备封装： | 8-MDIP |
| 包装： | 标准包装 |
| 其它名称： | FSL206MRBNFSDKR |
Line Under-Voltage Protection (LUVP)
If the input voltage of the converter is lower than the
minimum operating voltage, the converter input current
increases too much, causing components failure. If the
input voltage is low, the converter should be protected.
In the FSL206MR, the LUVP circuit senses the input
voltage using the LS pin and, if this voltage is lower than
1.5V, the LUVP signal is generated. The comparator
has 0.5V hysteresis. If the LUVP signal is generated, the
output drive block is shut down and the output voltage
feedback loop is saturated.
?
?
Burst Operation
To minimize power dissipation in Standby Mode, the
FPS enters Burst Mode. As the load decreases, the
feedback voltage decreases. As shown in Figure 23, the
device automatically enters Burst Mode when the
feedback voltage drops below V BURH . Switching
continues until the feedback voltage drops below V BURL .
At this point, switching stops and the output voltages
start to drop at a rate dependent on the standby current
load. This causes the feedback voltage to rise. Once it
passes V BURH , switching resumes. The feedback voltage
then falls and the process repeats. Burst Mode
alternately enables and disables switching of the
SenseFET and reduces switching loss in Standby Mode.
V O
Vo set
V FB
Figure 21.
Line UVP Circuit
V BURH
Soft-Start
The FSL206MR has an internal soft-start circuit that
slowly increases the feedback voltage, together with the
SenseFET current, after it starts. The typical soft-start
time is 15ms, as shown in Figure 22, where progressive
increments of the SenseFET current are allowed during
the startup phase. The pulse width to the power
switching device is progressively increased to establish
the correct working conditions for transformers,
inductors, and capacitors. The voltage on the output
capacitors is progressively increased with the intention
V BURL
I DS
V DS
of smoothly establishing the required output voltage. It
also helps prevent transformer saturation and reduce
the stress on the secondary diode.
t1
Switching
disabled
t2
t3
Switching
disabled
t4
time
Figure 23.
Burst-Mode Operation
Figure 22.
Internal Soft-Start
? 2011 Fairchild Semiconductor Corporation
FSL206MR ? Rev. 1.0.5
11
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSQ0265RLX | IC FPS PWR SWITCH VSC 8A 8-LSOP |
| FSQ0370RNA | IC SWIT PWM GREEN OVP UVLO 8DIP |
| FSQ0465RSWDTU | IC SWIT PWM GREEN OVP HV TO220F |
| FSQ0465RUWDTU | IC SWIT PWM GREEN UVLO HV TO220F |
| FSQ0565RQLDTU | IC PWM/SENSEFET QRC TO-220F-6L |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSL206MRL | 功能描述:电源开关 IC - 配电 Low Power FPS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSL206MRN | 功能描述:电源开关 IC - 配电 Low Power FPS RoHS:否 制造商:Exar 输出端数量:1 开启电阻（最大值）:85 mOhms 开启时间（最大值）:400 us 关闭时间（最大值）:20 us 工作电源电压:3.2 V to 6.5 V 电源电流（最大值）: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOT-23-5 |
| FSL214 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Radiation Hardened, SEGR Resistant N-Channel Power MOSFETs |
| FSL214D | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Radiation Hardened, SEGR Resistant N-Channel Power MOSFETs |
| FSL214D1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Radiation Hardened, SEGR Resistant N-Channel Power MOSFETs |
发布紧急采购，3分钟左右您将得到回复。