参数资料
| 型号： | FSQ500L |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 8/12页 |
| 文件大小： | 0K |
| 描述： | IC SWIT PWM GREEN UVLO SOT223 |
| 标准包装： | 1 |
| 系列： | FPS™ |
| 输出隔离： | 隔离 |
| 频率范围： | 120kHz ~ 140kHz |
| 输入电压： | 5.5 V ~ 10 V |
| 输出电压： | 700V |
| 功率（瓦特）： | 3W |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | TO-261-4，TO-261AA |
| 供应商设备封装： | SOT-223-3 |
| 包装： | 标准包装 |
| 其它名称： | FSQ500LFSDKR |
Functional Description
1. Startup and V CC Regulation : At startup, an internal
high-voltage current source supplies the internal bias
and charges the external capacitor (C A ) connected to
the V CC pin, as illustrated in Figure 15. An internal high-
voltage regulator (HV/REG) located between the D and
V O
FOD817A
V FB
C B
2
V CC V CC
I DELAY
D1
I FB
D2
8R
OSC
SenseFET
V CC pins regulates the V CC to be 6.5V and supplies
operating current. Therefore, FSQ500L needs no
auxiliary bias winding.
Transformer
KA431
V SD
+
V FB *
-
R
OLP
Gate
driver
R sense
D
C A
V CC
3
6.5V
I CH
I START
HV/REG
2
Figure 16. Pulse Width Modulation (PWM) Circuit
3. Protection Circuits : The FSQ500L has two self-
protective functions: overload protection (OLP) and
thermal shutdown (TSD). While OLP is implemented as
V REF
UVLO
auto-restart mode, there is no switching when TSD
triggers. Once the overload condition is detected,
switching is terminated, the senseFET remains off, and
Figure 15. Startup Block
2. Feedback Control : FSQ500L employs current mode
control, as shown in Figure 16. An opto-coupler (such as
the FOD817A) and shunt regulator (such as the KA431)
are typically used to implement the feedback network.
Comparing the feedback voltage with the voltage across
the R sense resistor makes it possible to control the
switching duty cycle. When the reference pin voltage of
the regulator exceeds the internal reference voltage of
2.5V, the opto-coupler LED current increases, pulling
down the feedback voltage and reducing the duty cycle.
This typically happens when the line input voltage
HV/REG turns off. This causes V CC to fall. When V CC
falls below the under voltage lockout (UVLO) stop
voltage of 5.0V, the protection is reset and the startup
circuit charges the V CC capacitor. When V CC reaches the
start voltage of 6.0V, the FSQ500L resumes its normal
operation. If the fault condition is still not removed, the
senseFET and HV/REG remain off and V CC drops to
V STOP again. In this manner, the auto-restart can
alternately enable and disable the switching of the
power senseFET until the fault condition is eliminated,
as shown in Figure 17.
Because these protection circuits are fully integrated
into the IC without external components, reliability is
improved without increasing cost.
increases or the output load current decreases.
2.1 Pulse-by-Pulse Current Limit : Because current
V DS
Power
on
OLP
occurs
OLP
removed
mode control is employed, the peak current through the
senseFET is limited by the non-inverting input of PWM
comparator (V FB *), as shown in Figure 16. Assuming
that 225μA current source flows only through the
internal resistor (8R + R = 12k Ω ), the cathode voltage of
diode D2 is about 2.7V. Since D1 is blocked when the
feedback voltage (V FB ) exceeds 2.7V, the maximum
voltage of the cathode of D2 is clamped at this voltage,
clamping V FB *. Therefore, the peak value of the current
through the senseFET is limited.
2.2 Leading-Edge Blanking (LEB) : At the instant the
internal senseFET is turned on, a high-current spike
V CC
6.5V
6.0V
5.0V
t
occurs through the senseFET, caused by primary-side
capacitance and secondary-side rectifier reverse
Normal
operation
Fault
situation
Normal
operation
recovery. Excessive voltage across the R sense resistor
would lead to incorrect feedback operation in the current
mode PWM control. To counter this effect, the FPS
employs a leading-edge blanking (LEB) circuit. This
circuit inhibits the PWM comparator for a short time (t LEB
= 250ns) after the senseFET turns on.
? 2008 Fairchild Semiconductor Corporation
FSQ500L ? Rev. 1.0.3
8
Figure 17. Auto Restart Protection Waveforms
www.fairchildsemi.com
相关PDF资料 |
PDF描述 |
|---|---|
| FSQ500N | IC PWM/SENSEFET 130KHZ 8-MDIP |
| FSQ510H | IC SWITCH FPS 0.5A 700V 8-DIP |
| FT435-30H | IC REG BOOST SYNC 3V 0.15A SOT23 |
| FT440CA | IC REG BUCK SYNC 1.8V 0.6A SOT23 |
| FT441AA | IC REG BUCK SYNC ADJ 0.9 A SOT23 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FSQ500L_09 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Compact, Green Mode, Fairchild Power Switch |
| FSQ500N | 功能描述:交流/直流开关转换器 Compact FPS RoHS:否 制造商:STMicroelectronics 输出电压:800 V 输入/电源电压（最大值）:23.5 V 输入/电源电压（最小值）:11.5 V 开关频率:115 kHz 电源电流:1.6 mA 工作温度范围:- 40 C to + 150 C 安装风格:SMD/SMT 封装 / 箱体:SSO-10 封装:Reel |
| FSQ510 | 功能描述:开关变换器、稳压器与控制器 SMPS Power Switch (QRC) 0.5A 700V RoHS:否 制造商:Texas Instruments 输出电压:1.2 V to 10 V 输出电流:300 mA 输出功率: 输入电压:3 V to 17 V 开关频率:1 MHz 工作温度范围: 安装风格:SMD/SMT 封装 / 箱体:WSON-8 封装:Reel |
| FSQ510_08 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch (FPS?) for Valley Switching Converter ? Low EMI and High Efficiency |
| FSQ510_09 | 制造商:FAIRCHILD 制造商全称:Fairchild Semiconductor 功能描述:Green Mode Fairchild Power Switch |
发布紧急采购，3分钟左右您将得到回复。