参数资料
| 型号： | FT10001FHX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 7/11页 |
| 文件大小： | 0K |
| 描述： | IC RESET TIMER 6-MICROPAK2 |
| 标准包装： | 5,000 |
| 类型： | 可编程计时器 |
| 电源电压： | 1.8 V ~ 5 V |
| 电流 - 电源： | 200µA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | * |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | * |
| 安装类型： | 表面贴装 |
2011 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FT10001 Rev 1.0.1
5
FT10001
—
Reset
Timer
with
Fixed
Delay
and
Reset
Pulse
Functional Description
Default operation time N is 10s. If the DSR pin is pulled
HIGH prior to VCC ramp, the FT10001 enters Test Mode
and the reset output, /RST1, is immediately pulled LOW
for factory testing. The DSR pin MUST be forced to
GND during normal operation. The DSR pin should
never be driven HIGH or left to FLOAT during normal
operation. The DSR PIN state should never be changed
during device operation; it must be biased prior to
supplying the VCC supply. If there is a need to use the
DSR=VCC Test Mode, the /SR0 must be HIGH when
the DSR pin is moved from LOW to HIGH to enter Zero-
Second Factory-Test Mode. To return to the standard
10-second reset time, the same procedure must be
followed with DSR=GND. The DSR pin should never be
allowed to change state while the /SR0 pin is LOW.
Operation Modes
A low input signal on /SR0 starts the oscillator. There
are two scenarios for counting: short duration and long
duration. In the short-duration scenario, output /RST1 is
not affected. In the long-duration scenario, the output
/RST1 goes LOW after /SR0 has been held LOW for
10s. The /RST1 output returns to its original HIGH
state 530ms after time tREC has expired, regardless of
the state of /SR0. The /RST1 output is an open-drain
driver. When the count time exceeds time 10s, the
/RST1 output pulls LOW.
Short Duration (tW < 10s)
When the /SR0 input goes LOW, the internal timer starts
counting. If the /SR0 input goes HIGH before 10s has
elapsed, the timer stops counting and resets and no
changes occur on the outputs.
Long Duration (tW > 10s)
When the /SR0 input goes LOW, the internal timer starts
counting. If the /SR0 input stays LOW for at least 10s, the
RST output is enabled and pulled LOW. The output RST
is held LOW for tREC, 530ms, as soon as the reset time
of 10s is met, regardless of the state of the /SR0 pin.
When the /SR0 input has returned HIGH and tREC has
expired, the internal timer resets and awaits the next
RESET event.
Zero-Second Test Mode
/RST1 goes LOW immediately after /SR0 goes LOW.
N=7.5s
tREC=530ms
Short-Duration,
Normal Operation
/RST1 never goes LOW because
/SR0 LOW duration does not meet
requirement: Reset Time N=10s
Long-Duration,
Normal Operation
/RST1 goes LOW because
/SR0 LOW duration exceeds
requirement: Reset Time N=10s
Zero-Second Factory-Test Mode
/RST1 goes LOW immediately
after /SR0 goes LOW
/SR0
RST1
/SR0
RST1
/SR0
RST1
Figure 3.
Reset Timing Waveforms
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BWL-MX-B1 | CONVERTER MOD DC/DC 28V 75W |
| MC14541BFELG | IC OSC PROG TIMER 3MHZ 14SOEIAJ |
| MAX199BEWI+ | IC DAS 12BIT 8CH 28-SOIC |
| MAX198ACWI+ | IC DAS 12BIT 6CH 28-SOIC |
| ADG3245BRUZ | IC SW BUS 2.5-3.3V 8BIT 20TSSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT10001L6X | 功能描述:计时器和支持产品 Reset Timer w/Fixed Delay & Reset Pulse RoHS:否 制造商:Micrel 类型:Standard 封装 / 箱体:SOT-23 内部定时器数量:1 电源电压-最大:18 V 电源电压-最小:2.7 V 最大功率耗散: 最大工作温度:+ 85 C 最小工作温度:- 40 C 封装:Reel |
| FT100-02 | 制造商:HAKKO Corporation 功能描述: |
| FT100-03 | 制造商:HAKKO Corporation 功能描述: |
| FT100-04 | 制造商:HAKKO Corporation 功能描述: |
| FT100-04-230120 | 制造商:ITW Pancon 功能描述: |
发布紧急采购，3分钟左右您将得到回复。