- 您现在的位置：买卖IC网 > PDF目录3927 > FT24C128A-USG-T (Fremont Micro Devices USA)IC EEPROM 128KBIT 1MHZ 8SOP PDF资料下载
参数资料
| 型号： | FT24C128A-USG-T |
| 厂商： | Fremont Micro Devices USA |
| 文件页数： | 5/15页 |
| 文件大小： | 0K |
| 描述： | IC EEPROM 128KBIT 1MHZ 8SOP |
| 标准包装： | 1 |
| 格式 - 存储器： | EEPROMs - 串行 |
| 存储器类型： | EEPROM |
| 存储容量： | 128K (16K x 8) |
| 速度： | 400kHz，1MHz |
| 接口： | I²C，2 线串口 |
| 电源电压： | 1.8 V ~ 5.5 V |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 8-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 8-SOP |
| 包装： | 标准包装 |
| 其它名称： | 1219-1106-6 |
24C128A,24C256A
WRITE OPERATIONS
(A) BYTE WRITE
A write operation requires two 8-bit data word address following the device address word and ACKNOWLEDGE
signal. Upon receipt of this address, the EEPROM will respond with a “0” and then clock in the first 8-bit data
word. Following receipt of the 8-bit data word, the EEPROM will again output a “0”. The addressing device, such
as a microcontroller, must terminate the write sequence with a STOP condition. At this time the EEPROM enters
into an internally-timed write cycle state. All inputs are disabled during this write cycle and the EEPROM will not
respond until the writing is completed (figure 3).
(B) PAGE WRITE
The128K/256K EEPROM are capable of 64-byte page write.
A page write is initiated the same way as a byte write, but the microcontroller does not send a STOP condition
after the first data word is clocked in. The microcontroller can transmit up to 63 more data words after the
EEPROM acknowledges receipt of the first data word. The EEPROM will respond with a “0” after each data word
is received. The microcontroller must terminate the page write sequence with a STOP condition (see Figure 4).
The lower six bits of the data word address are internally incremented following the receipt of each data word. The
higher data word address bits are not incremented, retaining the memory page row location. If more than 64 data
words are transmitted to the EEPROM, the data word address will “roll over” and the previous data will be
overwritten.
(C) ACKNOWLEDGE POLLING
ACKNOWLEDGE polling may be used to poll the programming status during a self-timed internal programming.
By issuing a valid read or write address command, the EEPROM will not acknowledge at the 9 th clock cycle if the
device is still in the self-timed programming mode. However, if the programming completes and the chip has
returned to the STANDBY mode, the device will return a valid ACKNOWLEDGE signal at the 9 th clock cycle.
READ OPERATIONS
The read command is similar to the write command except the 8 th read/write bit in address word is set to “1”. The three
read operation modes are described as follows:
(A) CURRENT ADDRESS READ
The EEPROM internal address word counter maintains the last read or write address plus one if the power supply
to the device has not been cut off. To initiate a current address read operation, the micro-controller issues a
START bit and a valid device address word with the read/write bit (8 th ) set to “1”. The EEPROM will response
with an ACKNOWLEDGE signal on the 9 th serial clock cycle. An 8-bit data word will then be serially clocked out.
The internal address word counter will then automatically increase by one. For current address read the micro-
controller will not issue an ACKNOWLEDGE signal on the 18 th clock cycle. The micro-controller issues a valid
STOP bit after the 18 th clock cycle to terminate the read operation. The device then returns to STANDBY mode
(see Figure 5).
(B) SEQUENTIAL READ
The sequential read is very similar to current address read. The micro-controller issues a START bit and a valid
device address word with read/write bit (8 th ) set to “1”. The EEPROM will response with an ACKNOWLEDGE
signal on the 9 th serial clock cycle. An 8-bit data word will then be serially clocked out. Meanwhile the internally
address word counter will then automatically increase by one.
? 2009 Fremont Micro Devices Inc.
DS3007J-page 5
相关PDF资料 |
PDF描述 |
|---|---|
| AYF533335 | CONN SOCKET FPC 0.5MM 33POS SMD |
| FT24C128A-USR-T | IC EEPROM 128KBIT 1MHZ 8SOP |
| AYF532665 | CONN SOCKET FPC 0.5MM 26POS SMD |
| FT24C32A-UNR-T | IC EEPROM 32KBIT 1MHZ 8DFN |
| FF0364SA1-R2000 | CONN FFC/FPC 0.5MM 64POS R/A SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT24C128A-USR-B | 功能描述:IC EEPROM 128KBIT 1MHZ 8SOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| FT24C128A-USR-T | 功能描述:IC EEPROM 128KBIT 1MHZ 8SOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| FT24C128A-UTG-B | 功能描述:IC EEPROM 128KBIT 1MHZ 8TSSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| FT24C128A-UTG-T | 功能描述:IC EEPROM 128KBIT 1MHZ 8TSSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
| FT24C128A-UTR-B | 功能描述:IC EEPROM 128KBIT 1MHZ 8TSSOP RoHS:是 类别:集成电路 (IC) >> 存储器 系列:- 标准包装:96 系列:- 格式 - 存储器:闪存 存储器类型:FLASH 存储容量:1M (64K x 16) 速度:150ns 接口:并联 电源电压:3 V ~ 3.6 V 工作温度:0°C ~ 70°C 封装/外壳:48-TFSOP（0.724"，18.40mm 宽） 供应商设备封装:48-TSOP 包装:托盘 |
发布紧急采购，3分钟左右您将得到回复。