- 您现在的位置：买卖IC网 > PDF目录1995 > FT8010UMX (Fairchild Semiconductor)IC RESET TIMER CONF DELAY 10UMLP PDF资料下载
参数资料
| 型号： | FT8010UMX |
| 厂商： | Fairchild Semiconductor |
| 文件页数： | 7/12页 |
| 文件大小： | 0K |
| 描述： | IC RESET TIMER CONF DELAY 10UMLP |
| 标准包装： | 5,000 |
| 类型： | 可编程计时器 |
| 电源电压： | 1.8 V ~ 5 V |
| 电流 - 电源： | 100µA |
| 工作温度： | -40°C ~ 85°C |
| 封装/外壳： | 10-UFQFN |
| 包装： | 带卷 (TR) |
| 供应商设备封装： | 10-UMLP |
| 安装类型： | 表面贴装 |
2009 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FT8010 Rev. 1.0.8
4
FT8010
—
Reset
Timer
with
Configurable
Delay
Time
Functional Description
The FT8010 reset timer uses an internal oscillator and a
two-stage, 21-bit counter to determine when the output
pins switch. Time N is set by the hard-wired logic level
of the DSR pin. N is either 7.5 ±20% seconds for
DSR=LOW or 11.25 ±20% seconds for DSR=HIGH.
Table 1.
FT8010 Truth Table
DSR
Reset Timer ( +-20% )
0
7.50s
1
11.25s
The two input pins, /SR0 and /SR1, drive voltage
comparators that compare the voltage on the input with
the voltage set by the reference block. A low input signal
on both /SR0 and /SR1 starts the oscillator. The
oscillator sends data pulses to the digital core, which
includes the counter. There are two scenarios for
counting, as described below: short duration and long
duration. In the short-duration scenario, outputs /RST1
and RST2 are not affected. In the long duration
scenario, the outputs change state after time N. The
outputs return to their original states when a HIGH input
signal occurs on either /SR0 or /SR1.
The /RST1 output is an open-drain driver. When the count
time exceeds time N, the /RST1 output drives LOW. The
RST2 output is a push-pull driver. When the count time
exceeds time N, the RST2 output drives HIGH.
The TRIG pin should be tied GND or LOW during
normal operation. The TRIG pin is a test mode pin used
for SCAN testing.
Application Note
IMPORTANT
: The DSR pin must be tied to VCC or GND
to provide a HIGH or LOW voltage level. The voltage
level on the DSR pin determines the length of the
configurable delay. It is important that the voltage level
on the DSR pin not change during normal operation.
The DSR pin must be tied directly to VCC or GND before
SR0 or SR1 buttons go LOW. Do not use pull-up or pull-
down resistors on the DSR pin.
Short Duration (tW < N)
In this case, both input /SR0 and /SR1 are LOW for a
duration tW which is shorter than time N. When an input
goes LOW, the internal timer starts counting. The input
goes HIGH before time N. The timer stops counting and
resets and no changes occur on the outputs (see Figure 4).
/SR0
/SR1
/RST1
/RST2
Description
L
H
L
The timer starts counting when both inputs go LOW. The timer stops
counting and resets when either input goes HIGH. No changes occur on the
outputs, Both /SR0 and /SR1 need to be LOW to activate (start) the timer.
L
H
L
Figure 4.
Short Duration Waveform
相关PDF资料 |
PDF描述 |
|---|---|
| FTS125-COO-010.0M | IC GPS BASED TIMING MOD (OCXO) |
| FTS125-CTV-010.0M | IC GPS BASED TIMING MOD (TCXO) |
| FTS250-010.0M | IC GPS BASED TIMING MOD (TCXO) |
| FTS375-010.0M | IC GPS BASED TIMING MOD (OCXO) |
| HD3-6408-9Z | IC ASMA ADT CMOS 1.25MHZ 24DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| FT8011 | 制造商:Black Box Corporation 功能描述:MINI NYL CABLE TIES 0.1"W X 4.0"L,BLK-100PK |
| FT801-31 | 功能描述:WIRE STRIPPER,THERMAL,DIGITAL,FT 制造商:american hakko products, inc. 系列:* 零件状态:在售 标准包装:1 |
| FT801Q-R | 功能描述:IC TFT LCD CONTROLLER 48VQFN 制造商:ftdi, future technology devices international ltd 系列:- 包装:剪切带（CT） 零件状态:有效 类型:控制器 应用:视频 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商器件封装:48-VQFN（7x7） 标准包装:1 |
| FT8020 | 制造商:Black Box Corporation 功能描述:MINI NYL CABLE TIES 0.1"W x 8.0"L,BLCK-100PK |
| FT805-E | 制造商:Black Box Corporation 功能描述:FT805 230V VERSION |
发布紧急采购，3分钟左右您将得到回复。