- 您现在的位置：买卖IC网 > PDF目录60232 > G2997 (Global Mixed-mode Technology Inc.) DDR Termination Regulator PDF资料下载
参数资料
| 型号： | G2997 |
| 厂商： | Global Mixed-mode Technology Inc. |
| 英文描述： | DDR Termination Regulator |
| 中文描述： | DDR终端稳压器 |
| 文件页数： | 9/10页 |
| 文件大小： | 597K |
| 代理商： | G2997 |
Ver: 1.1
Jul 06, 2006
TEL: 886-3-5788833
http://www.gmt.com.tw
8
G2997
Global Mixed-mode Technology Inc.
Description
VTT SINK/SOURCE REGULATOR
The G2997 is a 3A sink/source tracking termination
regulator designed specially for low-cost, low external
components system where space is at premium such
as notebook PC applications. The G2997 integrates
high performance low-dropout linear regulator that is
capable of sourcing and sinking current up to 3 A. This
VTT linear regulator is implemented with ultimately
fast response feedback loop so that small ceramic
capacitors are enough to keep tracking to the VTTREF
within 40mV at all conditions including fast load tran-
sient. To achieve tight regulation with minimum effect
of trace resistance, a remote sensing terminal,
VTTSNS, should be connected to the positive node of
VTT output capacitor as a separate trace from the high
current line from VTT.
VTTREF REGULATOR
The VTTREF block consists of an on-chip 1/2 divider,
LPF and buffer. This regulator can source/sink current
up to 10mA. Bypass VTTREF to GND using a 0.1F
ceramic capacitor to ensure stable operation. To en-
sure better start-up and transient performance, the
larger 1F ceramic capacitors are recommended.
Power on sequence
To operate safely, the G2997 must keep VIN voltage
larger than other Input-PIN voltage .This condition is
due to the internal parasitic diodes between VIN to
others PIN for ESD issue. If the VIN voltage is lower
than the other pins voltage, the G2997 will consume
extra current through the parasitic diodes during the
power-on period.
Soft-Start
The soft-start function of the VTT is achieved via a
current clamp, allowing the output capacitors to be
charged with low and constant current that gives linear
ramp up of the output voltage. The current limit
threshold is changed in two stages using an internal
powergood signal. When VTT is outside the power-
good threshold, the current limit level is 2A. When VTT
rises above (VTTREF - 5%) or falls below (VTTREF +
5%) the current limit level switches to 4 A. The thresh-
olds are typically VTTREF
5% (from outside regul
a-
tion to inside) and 10% (when it falls outside). The
soft-start function is completely symmetrical and it
works not only from GND to VTTREF voltage, but also
from VDDQSNS to VTTREF voltage. Note that the
VTT output is in a high impedance state during the S3
state (S3 = low, S5 = high) and its voltage can be up
to VDDQSNS voltage depending on the external con-
dition. Note that VTT does not start under a full load
condition.
S3, S5 Control and Soft-Off
The S3 and S5 terminals should be connected to
SLP_S3 and SLP_S5 signals respectively. Both
VTTREF and VTT are turned on at normal state (S3 =
high, S5 = high). VTTREF is kept alive while VTT is
turned off and left high impedance in standby state (S3
= low, S5 = high). Both VTT and VTTREF outputs are
turned off and discharged to the ground through inter-
nal MOSFETs during shutdown state (S5 = low). The
control function is showed on the Table 1.
Table 1. S3 and S5 Control Table
STATE
S3
S5
VTT
VREF
Normal
Hi
1.25V/0.9V
Standby
Lo
Hi
12mV/6mV
(High-Z)
1.25V/0.9V
Shutdown
Lo
0V
(Discharge)
0V
(Discharge)
Shutdown
Hi
Lo
0V
(Discharge)
0V
(Discharge)
VTT Current Protection
The LDO has a constant overcurrent limit (OCL) at 4A.
This trip point is reduced to 2A before the outputvolt-
age comes within 5% of the target voltage or goes
outside of 10% of the target voltage.
Input Capacitor
Adding a capacitance close to VLDOIN pin can improve
the VTT performance when fast load- transient. In gen-
eral, 1/2 COUT is recommended for the VLDOIN ca-
pacitance. Separating the VDDQSNS and VLDOIN pins
will get better transient performance. The recommended
capacitor types are tabulated in the Table 2.
Output Capacitor
For stable operation, total capacitance of the VTT
output terminal can be equal or greater than 20F.
The output capacitor should be located near VTT out-
put terminal as close as possible to minimize the effect
of ESR and ESL. The recommended capacitor types
are tabulated in the Table 2.
Table 2.
CAP
MANUF
PART NUMBER
C1
TAYO
YUDEN
EMK 325BJ106KD
C2
TAYO
YUDEN
UMK 212BJ104KG
相关PDF资料 |
PDF描述 |
|---|---|
| G2A | Glass Passivated Junction Rectifier(钝化玻璃结型整流器) |
| G2B | Glass Passivated Junction Rectifier(钝化玻璃结型整流器) |
| G2D | GLASS PASSIVATED JUNCTION RECTIFIER |
| G2G | GLASS PASSIVATED JUNCTION RECTIFIER |
| G2J | Glass Passivated Junction Rectifier(钝化玻璃结型整流器) |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G2997B | 制造商:GMT 制造商全称:Global Mixed-mode Technology Inc 功能描述:DDR Termination Regulator |
| G2997F6U | 制造商:GMT 制造商全称:Global Mixed-mode Technology Inc 功能描述:DDR Termination Regulator |
| G2997P7U | 制造商:GMT 制造商全称:Global Mixed-mode Technology Inc 功能描述:DDR Termination Regulator |
| G29AH | 功能描述:SW TOGGLE DPDT MOM RT ANGLE PC RoHS:是 类别:开关 >> 拨动开关 系列:G 标准包装:1 系列:A 电路:双刀双掷 开关功能:开-开-开 触点额定电压:6A @ 125VAC 触动器类型:扁平型 触动器长度:11.38mm 发光:不发光 安装类型:面板安装 端接类型:焊片 轴衬螺纹:1/4-40 包装:散装 |
| G29AH-RO | 功能描述:拨动开关 ON-OFF-(ON) DPDT RoHS:否 制造商:C&K Components 触点形式:DPDT 开关功能:ON - ON - ON 电流额定值: 电压额定值 AC:20 V 电压额定值 DC:20 V 功率额定值:0.4 VA 端接类型:V-Bracket 安装风格: 端子密封:Epoxy 触点电镀:Gold 照明:Not Illuminated |
发布紧急采购，3分钟左右您将得到回复。