- 您现在的位置：买卖IC网 > PDF目录223850 > G6JU-2FL-Y4.5VDC POWER/SIGNAL RELAY, DPDT, LATCHED, 0.022A (COIL), 4.5VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT PDF资料下载
参数资料
| 型号： | G6JU-2FL-Y4.5VDC |
| 元件分类： | 功率/信号继电器 |
| 英文描述： | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.022A (COIL), 4.5VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
| 文件页数： | 2/10页 |
| 文件大小： | 241K |
| 代理商： | G6JU-2FL-Y4.5VDC |
90
G6J-Y
Precautions
Refer to page 25 for information on general precautions. Be sure to read these precautions before using the Relay.
Correct Use
Long Term Current Carrying
Under a long-term current carrying without switching, the
insulation resistance of the coil goes down gradually due to the
heat generated by the coil itself. Furthermore, the contact
resistance of the Relay will gradually become unstable due to the
generation of film on the contact surfaces. A Latching Relay can
be used to prevent these problems. When using a single-side
stable relay, the design of the fail-safe circuit provides protection
against contact failure and open coils.
Handling of Surface-mounting Relays
Use the Relay as soon as possible after opening the moisture-
proof package. If the Relay is left for a long time after opening the
moisture-proof package, the appearance may suffer and seal
failure may occur after the solder mounting process. To store the
Relay after opening the moisture-proof package, place it into the
original package and sealed the package with adhesive tape.
When washing the product after soldering the Relay to a PCB,
use a water-based solvent or alcohol-based solvent, and keep the
solvent temperature to less than 40°C. Do not put the relay in a
cold cleaning bath immediately after soldering.
Soldering
Soldering temperature: Approx. 250°C (At 260°C if the DWS
method is used.)
Soldering time: Approx. 5 s max. (Approx. 2 s for the first time and
approx. 3 s for the second time if the DWS method is used.)
Be sure to adjust the level of the molten solder so that the solder
will not overflow onto the PCB.
Claw Securing Force During Automatic Insertion
During automatic insertion of Relays, make sure to set the
securing force of the claws to the following values so that the
Relay characteristics will be maintained.
Environmental Conditions During Operation, Storage, and
Transportation
Protect the Relays from direct sunlight and keep the Relays under
normal temperature, humidity, and pressure.
Mounting Latching Relays
Make sure that the vibration or shock that is generated from other
devices, such as Relays in operation, on the same panel and
imposed on the Latching Relays does not exceed the rated value,
otherwise the Latching Relays that have been set may be reset or
vice versa. The Latching Relays are reset before shipping. If
excessive vibration or shock is imposed, however, the Latching
Relays may be set accidentally. Be sure to apply a reset signal
before use.
Maximum Voltage
The maximum voltage of the coil can be obtained from the coil
temperature increase and the heat-resisting temperature of coil
insulating sheath material. (Exceeding the heat-resisting
temperature may result in burning or short-circuiting.) The
maximum voltage also involves important restrictions which
include the following:
Must not cause thermal changes or deterioration of the insulating
material.
Must not cause damage to other control devices.
Must not cause any harmful effect on people.
Must not cause fire.
Therefore, be sure not to exceed the maximum voltage specified
in the catalog.
As a rule, the rated voltage must be applied to the coil. A voltage
exceeding the rated value, however, can be applied to the coil
provided that the voltage is less than the maximum voltage. It
must be noted that continuous voltage application to the coil will
cause a coil temperature increase thus affecting characteristics
such as electrical life and resulting in the deterioration of coil
insulation.
Coating
Relays mounted on PCBs may be coated or washed. Do not
apply silicone coating or detergent containing silicone, otherwise
the silicone coating or detergent may remain on the surface of the
Relays.
Other Handling
Please don’t use the relay if it suffered the dropping shock.
Because there is a possibility of something damage for initial
performance.
A
C
B
Direction A: 4.90 N max.
Direction B: 9.80 N max.
Direction C: 9.80 N max.
Secure the claws to the area indicated by shading.
Do not attach them to the center area or to only part of the Relay.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
Cat. No. K125-E1-02
相关PDF资料 |
PDF描述 |
|---|---|
| G6JU-2FL-Y5VDC | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.02A (COIL), 5VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
| G6JU-2FS-Y-TR12VDC | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.009A (COIL), 12VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
| G6JU-2FS-Y-TR3VDC | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.034A (COIL), 3VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
| G6JU-2FS-Y-TR5VDC | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.02A (COIL), 5VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
| G6JU-2FS-Y12VDC | POWER/SIGNAL RELAY, DPDT, LATCHED, 0.009A (COIL), 12VDC (COIL), 100mW (COIL), 1A (CONTACT), 30VDC (CONTACT), SURFACE MOUNT-STRAIGHT |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G6JU2FLYDC12 | 制造商:Omron Electronic Components LLC 功能描述:EM RLY DPDT 1A 12VDC 1.3292KOHM SMD - Rail/Tube 制造商:Omron Electronic Components LLC 功能描述:RELAY TELECOM DPDT 1A 12V |
| G6JU-2FL-Y-DC12 | 功能描述:低信号继电器 - PCB Gullwing 1Coil Latch DPDT 12VDC 140mW RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗: |
| G6JU2FLYDC24 | 制造商:Omron Electronic Components LLC 功能描述:EM RLY DPDT 1A 24VDC SMD - Rail/Tube 制造商:Omron Electronic Components LLC 功能描述:RELAY TELECOM DPDT 1A 24V |
| G6JU-2FL-Y-DC24 | 功能描述:低信号继电器 - PCB Gullwing 1Coil Latch DPDT 24VDC 230mW RoHS:否 制造商:NEC 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 V 最大开关电流:1 A 线圈电流:1 A 线圈类型:Non-Latching 功耗:140 mW 端接类型:SMT 绝缘: 介入损耗: |
| G6JU2FLYDC3 | 制造商:Omron Electronic Components LLC 功能描述:EM RLY DPDT 1A 3VDC 89OHM SMD - Rail/Tube 制造商:Omron Electronic Components LLC 功能描述:RELAY TELECOM DPDT 1A 3V 制造商:Omron 功能描述:Electromechanical Relay DPDT 1A 3VDC 89Ohm Surface Mount |
发布紧急采购，3分钟左右您将得到回复。