- 您现在的位置：买卖IC网 > PDF目录7366 > G6K-2F-RF-TR09 DC12 (Omron Electronics Inc-EMC Div)RELAY RF DPDT 1A 12V PDF资料下载
参数资料
| 型号： | G6K-2F-RF-TR09 DC12 |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 6/8页 |
| 文件大小： | 0K |
| 描述： | RELAY RF DPDT 1A 12V |
| 标准包装： | 900 |
| 系列： | G6K-RF |
| 继电器类型： | RF |
| 线圈类型： | 无锁存 |
| 线圈电流： | 9.1mA |
| 线圈电压： | 12VDC |
| 触点形式： | DPDT（2 C 型） |
| 触点额定值（电流）： | 1A |
| 切换电压： | 125VAC，60VDC - 最小值 |
| 关闭电压（最大）： | 9.6 VDC |
| 关闭电压（最小）： | 1.2 VDC |
| 特点： | 1 GHz |
| 安装类型： | 表面贴装 |
| 端接类型： | 鸥翼型 |
| 包装： | 带卷 (TR) |
| 触点材料： | Silver（Ag），Gold（Au） |
| 操作时间： | 3ms |
| 释放时间： | 3ms |
| 线圈功率： | 100 mW |
| 线圈电阻： | 1.31 千欧 |
| 工作温度： | -40°C ~ 70°C |
| 其它名称： | G6K2FRFTR09DC12 |
Precautions
■ Recommended Soldering Method
1. Temperature Profile for Lead Solder (Measured at the PCB)
2. Temperature Profile for Lead-free Solder (Measured at the PCB)
Case top panel
(peak): 255 ° C max.
220 to
245
180 to
Solderin g
250 max.
230
180
Solderin g
200
Preheatin g
150
Preheatin g
150
Relay terminal
section
120 max.
30 max.
90 to 120
20 to 30
Time (s)
Time (s)
3. The thickness of cream solder to be applied should be between 200 and 250 μ m and the land pattern should be based on Omron’s recommended
PCB pattern. To maintain the correct soldering joint shown in the following diagram, we recommend applying solder using the soldering conditions
shown above. Check the soldering in the actual mounting conditions prior to use.
Relay
PCB
Terminal
Solder
Land
Insufficient
amount of
solder
Excessive
amount of
solder
■ Precautions for correct use
For general precautions, refer to Omron’s Relay Technical guidelines, contained in Omron’s relay catalog.
Relay Handling
Do not unpack the relay until ready to mount it. Use the relay as soon as
possible after opening the moisture-proof bag. Otherwise, the terminals
may tarnish and seal failure may occur after the solder process.
Claw Securing Force During Automatic Mounting
During automatic insertion of relays, make sure to set the securing
force of each claw to the following so that the relay’s characteristics
will be maintained.
When washing the product after soldering, use a water-based or
alcohol-based solvent. Keep the solvent temperature below 40 ° C.
Do not put the relay in a cold cleaning bath immediately after soldering.
A
C
B
Direction A: 1.96 N max.
Direction B: 4.90 N max.
Direction C: 1.96 N max.
Operating, Storage Environment
If the relay is stored for a long time in an adverse environment with high
temperature, high humidity, organic or sulfide gases, then sulfide or
oxide films will form on the contact surfaces. These films may result in
unstable contact, contact problems or function problems. Therefore,
operate, store or transport the product under specified environmental
conditions.
1. Use in locations where the relay is not exposed to corrosive
gas such as hydrogen sulfide gas or salty air.
2. Use in locations where no visible dust exists.
3. Use, store and transport in locations where the product is not
exposed to direct sunlight, rain or snow.
4. Do not apply force to the product which may result in deformation
or change in quality of the product.
Coating
The relay mounted on the PCB may be coated or washed, but do not
apply silicone coating or detergent containing silicone, otherwise, the
silicone coating or detergent may remain on the surface of the relay.
Latching Relay Mounting
Make sure that excess vibration or shock doesn’t set or reset the
relay during normal operation. The relay is shipped in the ‘reset’
position. Shock or vibration during shipping may require the application
of a reset signal, prior to operation.
Secure the claws to the shaded area. Do not
attach them to the center of the relay or just
one part of the relay.
Maximum Allowable Voltage
The maximum allowable voltage of the coil can be obtained from the
coil temperature increase and the heat-resisting temperature of the
coil insulating sheath material. (Exceeding the heat-resisting tem-
perature may result in burning or short-circuiting.) The maximum
allowable voltage also involves important restrictions which include
the following;
? Must not cause thermal changes in or deterioration of the insulating
material, which may result in films developing on the contacts.
? Must not cause damage to other control devices.
? Must not cause any harmful effect on people.
? Must not cause fire.
Therefore, be sure to use the maximum allowable voltage as specified in
the catalog. As a rule, the rated voltage must be applied to the coil. Con-
sider using a latching relay instead of a non-latching relay with a continu-
ous voltage applied to the coil.
Long-term, Continuous ON contacts
Using the relay where it will remain continuously energized for long
periods of time can lead to unstable contacts. We recommend using
a latching relay for this type of application.
104
High Frequency Relay
G6K-RF
相关PDF资料 |
PDF描述 |
|---|---|
| 325118-04-0 | TERM BARRIER 4CIRC SGL ROW .325 |
| 325108-04-0 | TERM BARRIER 4CIRC SGL ROW .325 |
| 794956-3 | CONN SOCKT 18-22AWG PHOS BRZ TIN |
| OSTYK33306030 | CONN BARRIER STRIP 6CIRC 8.25MM |
| 4608X-102-332FLF | RES ARRAY 3.3K OHM 4 RES 8-SIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G6K2FRFTR09DC5 | 制造商:Omron Electronic Components LLC 功能描述:SURFACE MOUNT RELAY - Tape and Reel 制造商:Omron Electronic Components LLC 功能描述:RELAY RF DPDT 1A 5V |
| G6K-2F-RF-TR09DC5 | 功能描述:RELAY RF DPDT 1A 5V RoHS:是 类别:继电器 >> 信号，高达 2 A 系列:G6K-RF 标准包装:25 系列:700 继电器类型:舌簧 线圈类型:无锁存 线圈电流:12mA 线圈电压:12VDC 触点形式:SPST-NO（1 A 型） 触点额定值（电流）:500mA 切换电压:200VDC - 最小值 关闭电压（最大）:8 VDC 关闭电压（最小）:1 VDC 特点:静电屏蔽 安装类型:通孔 端接类型:PC 引脚 包装:管件 触点材料:- 操作时间:1ms 释放时间:1ms 线圈功率:- 线圈电阻:1 千欧 工作温度:-40°C ~ 85°C |
| G6K-2F-RF-TR09-DC5 | 制造商: 功能描述: 制造商:Omron Corporation 功能描述: 制造商:Omron Corporation 功能描述:SIGNAL RELAYS SURFACE MOUNT RELAY |
| G6K-2F-RF-T-TR03 DC12 | 功能描述:高频/射频继电器 3GHz SpSavGrd NoLtch DPDT 12DC 100mW T300 RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| G6K-2F-RF-T-TR03 DC24 | 功能描述:高频/射频继电器 3GHz SpSavGrd NoLtch DPDT 24DC 100mW T300 RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
发布紧急采购，3分钟左右您将得到回复。