参数资料
| 型号： | G6Y-1 DC24 |
| 厂商： | Omron Electronics Inc-EMC Div |
| 文件页数： | 5/6页 |
| 文件大小： | 0K |
| 描述： | RELAY RF SPDT 10MA 24V |
| 产品培训模块： | Medical Solutions |
| 产品目录绘图： | G6Y-1 Series G6Y Series High Freq Circuit G6Y Series High Freq Footprint |
| 标准包装： | 100 |
| 系列： | G6Y |
| 继电器类型： | RF |
| 线圈类型： | 无锁存 |
| 线圈电流： | 8.3mA |
| 线圈电压： | 24VDC |
| 触点形式： | SPDT（1 C 型） |
| 触点额定值（电流）： | 10mA |
| 切换电压： | 30VAC，30VDC - 最小值 |
| 关闭电压（最大）： | 18 VDC |
| 关闭电压（最小）： | 2.4 VDC |
| 特点： | 密封式 - 全部 |
| 安装类型： | 通孔 |
| 端接类型： | PC 引脚 |
| 包装： | 散装 |
| 触点材料： | 铜（Cu），金（Au） |
| 操作时间： | 10ms |
| 释放时间： | 5ms |
| 线圈功率： | 200 mW |
| 线圈电阻： | 2.88 千欧 |
| 工作温度： | -40°C ~ 70°C |
| 产品目录页面： | 2590 (CN2011-ZH PDF) |
| 其它名称： | G6Y 8001A G6Y-1-DC24 G6Y124DC G6Y1DC24 Z121 |
Examples of Mounting Designs
Since this example emphasizes reducing mounting costs, expensive
mounting methods such as through-hole boards are not shown. If
such methods are to be used, the characteristics must be studied
carefully using the actual board configuration.
Using a Double-sided Paper Epoxy Board
When double-sided paper epoxy boards are used, the dielectric
constant will be approximately the same as that of glass epoxy
boards ( ε r =4.8).
The width of the Strip Lines for a board with t=1.6 mm is 2.7 mm for
50 Ω and 1.3 mm for 75 Ω . For a board with t=1.0 mm the width is
1.7 mm for 50 Ω and 0.8 mm for 75 Ω .
The following diagram shows an example pattern and the Micro Strip
Lines connected to the contact terminals are formed with pattern
widths derived from the description above. The width between the
Micro Strip Lines and ground patterns are comparable to the
Micro Strip Line width.
There are jumpers between the upper and lower patterns at the
points marked with Xs in the diagram. Improved characteristics can
be obtained with more jumper locations. This method yields isolation
characteristics of 65 dB to 75 dB at 500 MHz and 50 dB at 900 MHz.
The metal plate must be attached to the base as described here.
From this point, the methods used for Strip Line design are the same
as for the double-sided board.
Mounting Precautions
Be sure to securely attach the Relay’s base surface to the board
during installation. The isolation characteristics will be affected if the
Relay lifts off the board.
As shown in the enlarged illustration of the cross-section of part A,
the G6Y is designed to ensure better high-frequency characteristics
if the stand-off part of the G6Y is in contact with the ground pattern of
the PCB. Therefore, the ground terminal and stand-off part are
electrically connected internally.
Should the through hole electrically connected to the contact
terminal come in contact with the stand-off part, the contact will be
short-circuited with the ground, which may cause an accident.
As a preventive measure, keep at least a distance of 0.3 mm
between the stand-off part and the through hole or land.
For example, if the terminal hole on the PCB is 1 mm in diameter and
the length B shown in the illustration is 1.4 mm, a distance of 0.3 mm
or more will be provided between the through hole and stand-off part.
PCB Mounting
At this point in the diagram the component side is the entire ground
pattern side, but set aside approximately 2.0 mm × 2.0 mm of the
pattern for the contact terminals and coil terminals.
Strip Line
Part A
Cross-section of Part A
G6Y
Coil
Using a Single-sided Board
When a single-sided board is used, isolation characteristics of only
60 dB to 70 dB at 200 MHz can be obtained. When high frequency
bands are to be used with a single-sided board, a metal plate can be
placed between the base and Relay and connected to the ground
pattern.
Metal plate
Ground terminals
G6Y
Metal plate
Printed circuit board
Pattern
With this method a metal plate is placed between the Relay and base
and connected to the pattern, as shown in the above diagram. The
important point here is that 3 locations (the G6Y’s ground terminal,
the metal plate’s bent tabs (A), and the ground pattern) are soldered
together at the same time. This method combines an inexpensive
single-sided board and inexpensive metal plate to yield the same
characteristics as a double-sided board. Good characteristics are
obtained by grounding the G6Y’s ground terminal and metal plate in
the same place.
Stand-off
part
Through
hole
Ground terminal
Ground
pattern
Contact
terminal
Ground terminal
High Frequency Relay
G6Y
339
相关PDF资料 |
PDF描述 |
|---|---|
| 84140200 | SSR GN2 DUAL 40A/240VAC 4-15VDC |
| 0395121515 | 3.81MM EURO HEADER RA BLK 15POS |
| G6Y-1 DC12 | RELAY RF SPDT 10MA 12V |
| 84140210 | SSR GN2 DUAL 40A/240VAC 17-32VDC |
| 0395365013 | 5.08MM EURO HEADER RA GRN 13POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| G6Y-1-DC4.5 | 功能描述:高频/射频继电器 900MHz SPDT 4.5VDC RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| G6Y1DC45 | 制造商:Omron Electronic Components LLC 功能描述:RELAY RF SPDT 10MA 4.5V |
| G6Y1DC5 | 制造商:Omron Electronic Components LLC 功能描述:Electromechanical Relay SPDT 0.5A 5VDC 125Ohm Through Hole 制造商:Omron Electronic Components LLC 功能描述:EM RLY SPDT 0.5A 5VDC 125OHM TH - Bulk 制造商:Omron Electronic Components LLC 功能描述:RELAY RF SPDT 10MA 5V 制造商:Omron 功能描述:Electromechanical Relay SPDT 0.5A 5VDC 125Ohm Through Hole |
| G6Y-1-DC5 | 功能描述:高频/射频继电器 900MHz SPDT 5VDC RoHS:否 制造商:Omron Electronics 触点形式:2 Form C (DPDT-BM) 触点电流额定值: 线圈电压:5 VDC 线圈类型:Non-Latching 频率: 功耗:100 mW 端接类型:Solder Terminal 绝缘:20 dB to 30 dB at 1 GHz 介入损耗:0.2 dB at 1 GHz |
| G6Y-1-DC5 | 制造商:Omron Electronic Components LLC 功能描述:High Frequency PCB Relay |
发布紧急采购，3分钟左右您将得到回复。