- 您现在的位置：买卖IC网 > PDF目录383015 > GS7025-CTM (Electronic Theatre Controls, Inc.) Serial Digital Receiver PDF资料下载
参数资料
| 型号： | GS7025-CTM |
| 厂商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Serial Digital Receiver |
| 中文描述： | 串行数字接收机 |
| 文件页数： | 11/13页 |
| 文件大小： | 134K |
| 代理商： | GS7025-CTM |
GENNUM CORPORATION
522 - 80 - 00
11
G
5. OUTPUT DATA MUTING
The GS7025 internally mutes the SDO and SDO outputs
when the device is not locked. When muted, SDO/SDO are
latched providing a logic state to the subsequent circuit
and avoiding a condition where noise could be amplified
and appear as data.
The output data muting timing is shown in Figure 12.
Fig. 12 Output Data Muting Timing
6. CLOCK ENABLE
When CLK_EN is high, the GS7025 SCO/SCO outputs are
enabled. When CLK_EN is low, the SCO/SCO outputs are
placed in a high Z state and float to V
CC
. Disabling the
clock outputs results in a power savings of 10%. It is
recommended that the CLK_EN input be hard wired to the
desired state. For applications which do not require the
clock output, connect CLK_EN to Ground and connect the
SCO/SCO outputs to V
CC
.
7. STRESSFULL DATA PATTERNS
All PLL's are susceptible to stressful data patterns which
can introduce bit errors in the data stream. PLL's are most
sensitive to patterns which have long run lengths of 0's or
1's (low data transition densities for a long period of time).
The GS7025 is designed to operate with low data transition
densities such as the SMPTE 259M-C pathological signal
(data transition density = 0.05).
8. I/O DESCRIPTION
8-1. High Speed Analog Inputs (SDI/SDI)
SDI/SDI are high impedance inputs which accept
differential or single-ended input drive.
Figure 13 shows the recommended interface when a single-
ended serial digital signal is used.
Fig. 13
8-2. High Speed Digital Inputs (DDI/DDI)
DDI/DDI are high impedance inputs which accept
differential or single-ended input drive. Two conditions must
be observed when interfacing to these inputs:
1. Input signal amplitudes are between 200 and 2000mV.
2. The common mode input voltage range is as specified
in the DC Characteristics table.
Commonly used interface examples are shown in Figures
14 to 16.
Figure 14 illustrates the simplest interface to the GS7025
digital inputs. In this example, the driving device generates
the PECL level signals (800mV amplitudes) having a
common mode input range between 0.4 and 4.6V. This
scheme is recommended when the trace lengths are less
than 1in. The value of the resistors depends on the output
driver circuitry.
Fig. 14
When trace lengths become greater than 1in, controlled
impedance traces should be used. The recommended
interface is shown in Figure 15. In this case, a parallel
resistor (R
LOAD
) is placed near the GS7025 inputs to
terminate the controlled impedance trace. The value of
R
LOAD
should be twice the value of the characteristic
impedance of the trace. In addition, place series resistors
(R
SOURCE
) near the driving chip to serve as source
terminations. They should be equal to the value of the trace
impedance. Assuming 800mV output swings at the driver,
R
LOAD
= 100
, R
SOURCE
= 50
and Z
O
= 50
.
Fig. 15
Figure 16 shows the recommended interface when the
GS7025 digital inputs are driven single-endedly. In this
case, the input must be AC-coupled and a matching
resistor (Zo) must be used.
Fig. 16
When the DDI and the DDI inputs are not used, saturate
one input of the differential amplifier for improved noise
immunity. To saturate, connect either pins 44 and 1 or pins
2 and 3 to V
CC
. Leave the other pair floating.
LOCK
DDI
SDO
VALID
DATA
NO DATA TRANSITIONS
VALID
DATA
OUTPUTS MUTED
SDI
GS7025
SDI
75
10nF
10nF
75
113
DDI
DDI
GS7025
DDI
DDI
R
SOURCE
R
LOAD
R
SOURCE
Z
O
Z
O
GS7025
DDI
DDI
Z
O
GS7025
相关PDF资料 |
PDF描述 |
|---|---|
| GS702 | Flexible Remote Control (FRC) Technology ? Transmitter |
| GS70328SJ-10IT | 32K x 8 256Kb Asynchronous SRAM |
| GS70328SJ-10T | 32K x 8 256Kb Asynchronous SRAM |
| GS70328SJ-12IT | 32K x 8 256Kb Asynchronous SRAM |
| GS70328TS-8T | 32K x 8 256Kb Asynchronous SRAM |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GS7032 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:32K x 8 256Kb Asynchronous SRAM |
| GS70328GJ-12 | 制造商:GSI Technology 功能描述: |
| GS70328GS-10 | 制造商:GSI Technology 功能描述:32K X 8 (256K) FAST ASYNCH SRAM 3.3V - Trays |
| GS70328GS-10I | 制造商:GSI Technology 功能描述:32K X 8 (256K) FAST ASYNCH SRAM 3.3V - Trays |
| GS70328GS-12 | 制造商:GSI Technology 功能描述:32K X 8 (256K) FAST ASYNCH SRAM 3.3V - Trays |
发布紧急采购，3分钟左右您将得到回复。