- 您现在的位置：买卖IC网 > PDF目录385329 > GS864218B-V (GSI TECHNOLOGY) 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs PDF资料下载
参数资料
| 型号： | GS864218B-V |
| 厂商： | GSI TECHNOLOGY |
| 英文描述： | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| 中文描述： | 4米× 18，200万× 36，100万× 72 72Mb的S /双氰胺同步突发静态存储器 |
| 文件页数： | 27/35页 |
| 文件大小： | 934K |
| 代理商： | GS864218B-V |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页当前第27页第28页第29页第30页第31页第32页第33页第34页第35页
Preliminary
GS864218/36/72(B/C)-xxxV
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
Rev: 1.03 6/2006
27/35
2004, GSI Technology
SAMPLE/PRELOAD
SAMPLE/PRELOAD is a Standard 1149.1 mandatory public instruction. When the SAMPLE / PRELOAD instruction is
loaded in the Instruction Register, moving the TAP controller into the Capture-DR state loads the data in the RAMs input and
I/O buffers into the Boundary Scan Register. Boundary Scan Register locations are not associated with an input or I/O pin, and
are loaded with the default state identified in the Boundary Scan Chain table at the end of this section of the datasheet. Because
the RAM clock is independent from the TAP Clock (TCK) it is possible for the TAP to attempt to capture the I/O ring contents
while the input buffers are in transition (i.e. in a metastable state). Although allowing the TAP to sample metastable inputs will
not harm the device, repeatable results cannot be expected. RAM input signals must be stabilized for long enough to meet the
TAPs input data capture set-up plus hold time (tTS plus tTH). The RAMs clock inputs need not be paused for any other TAP
operation except capturing the I/O ring contents into the Boundary Scan Register. Moving the controller to Shift-DR state then
places the boundary scan register between the TDI and TDO pins.
EXTEST
EXTEST is an IEEE 1149.1 mandatory public instruction. It is to be executed whenever the instruction register is loaded with
all logic 0s. The EXTEST command does not block or override the RAM’s input pins; therefore, the RAM’s internal state is
still determined by its input pins.
Typically, the Boundary Scan Register is loaded with the desired pattern of data with the SAMPLE/PRELOAD command.
Then the EXTEST command is used to output the Boundary Scan Register’s contents, in parallel, on the RAM’s data output
drivers on the falling edge of TCK when the controller is in the Update-IR state.
Alternately, the Boundary Scan Register may be loaded in parallel using the EXTEST command. When the EXTEST instruc-
tion is selected, the sate of all the RAM’s input and I/O pins, as well as the default values at Scan Register locations not asso-
ciated with a pin, are transferred in parallel into the Boundary Scan Register on the rising edge of TCK in the Capture-DR
state, the RAM’s output pins drive out the value of the Boundary Scan Register location with which each output pin is associ-
ated.
IDCODE
The IDCODE instruction causes the ID ROM to be loaded into the ID register when the controller is in Capture-DR mode and
places the ID register between the TDI and TDO pins in Shift-DR mode. The IDCODE instruction is the default instruction
loaded in at power up and any time the controller is placed in the Test-Logic-Reset state.
SAMPLE-Z
If the SAMPLE-Z instruction is loaded in the instruction register, all RAM outputs are forced to an inactive drive state (high-
Z) and the Boundary Scan Register is connected between TDI and TDO when the TAP controller is moved to the Shift-DR
state.
RFU
These instructions are Reserved for Future Use. In this device they replicate the BYPASS instruction.
相关PDF资料 |
PDF描述 |
|---|---|
| GS864218GB-167IV | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-167V | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-200IV | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-200V | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-250IV | 4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
相关代理商/技术参数 |
参数描述 |
|---|---|
| GS864218GB-167IV | 制造商:GSI 制造商全称:GSI Technology 功能描述:4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-167V | 制造商:GSI 制造商全称:GSI Technology 功能描述:4M x 18, 2M x 36, 1M x 72 72Mb S/DCD Sync Burst SRAMs |
| GS864218GB-200 | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V/3.3V 72MBIT 4MX18 7.5NS/3NS 119FBGA - Trays |
| GS864218GB-200I | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 2.5V/3.3V 72MBIT 4MX18 7.5NS/3NS 119FBGA - Trays |
| GS864218GB-200IV | 制造商:GSI Technology 功能描述:SRAM SYNC DUAL 1.8V/2.5V 72MBIT 4MX18 7.5NS/3NS 119FBGA - Trays |
发布紧急采购，3分钟左右您将得到回复。