参数资料
| 型号： | HA456CM |
| 厂商： | Intersil |
| 文件页数： | 11/13页 |
| 文件大小： | 0K |
| 描述： | IC VIDEO CROSSPOINT SWIT 44PLCC |
| 标准包装： | 26 |
| 功能： | 视频交叉点开关 |
| 电路： | 1 x 8:8 |
| 电压电源： | 双电源 |
| 电压 - 电源，单路/双路(±)： | ±4.5 V ~ 5.5 V |
| 电流 - 电源： | 68mA |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 44-LCC（J 形引线） |
| 供应商设备封装： | 44-PLCC |
| 包装： | 管件 |
7
FN4153.7
September 26, 2008
Figure 2 shows a typical application of the HA456 with
HFA1412 quad, gain-of-two buffers at the outputs to drive
75
Ω loads. This application shows the HA456 digital-switch
control interface set up in the 7-bit parallel mode. The HA456
uses 7 data lines and 3 control lines (WR, CE and LATCH).
The input/output information is presented to the chip at A2:0
and D3:0 by a parallel printer port. The data is stored in the
Master Registers on the rising edge of WR. When the
LATCH line goes high, the switch configuration loads into the
Slave Registers, and all 8 outputs reconfigure at the same
time. Each 7-bit word updates only one output at a time.
If several outputs are to be updated, the data is individually
loaded into the Master Registers. Then, a single LATCH
pulse can reconfigure all channels simultaneously.
An IBM compatible PC loads the programming data into the
HA456 via its parallel port (LPT1) using a simple BASIC
program.
TABLE 1. PARALLEL INTERFACE COMMANDS
A2:0
D3:0
ACTION
Selects
Output
Being
Programmed
0000 to 0111
Connect the input defined by D3:0 to the output selected by A2:0. Doesn’t enable a disabled output.
1000
Connect the output selected by A2:0 to GND. Doesn’t enable a disabled output.
1011
Asynchronously disable the single output selected by A2:0, and leave the Master Register unchanged.
1100
Asynchronously enable the single output selected by A2:0, and leave the Master Register unchanged.
Address
Inputs are
Irrelevant for
These
Functions
1101
Asynchronously disable all outputs, and leave the Master Register unchanged.
1110
Asynchronously enable all outputs, and leave the Master Register unchanged.
1111
Send a Software “Latch” pulse to the Slave Register to load it from the Master Register, iff, the LATCH input = 1.
If the LATCH input = 0, then this command is a NOP. The Master Register is unchanged by this command.
1001 or 1010
Do not use these codes in the parallel programming mode. These codes are for serial programming only.
TABLE 2. SERIAL INTERFACE COMMANDS
D3:0
ACTION
0000 to 0111
Connect the output to the input channel defined by D3:0. Doesn’t enable a disabled output.
1000
Connect the output to GND. Doesn’t enable a disabled output.
1001
Enable the output and connect it to GND. The default power-up state is all outputs disabled, so use this code to enable
outputs after power is applied, but before programming the switch configuration.
1010
Disable the output. The output is no longer associated with any input channel; the desired input must be redefined after
re enabling the output.
1011 to 1111
Do not use these codes in the serial programming mode.
TABLE 3. DEFINITION OF DATA AND ADDRESS BIT FUNCTIONS
SER/PAR
D3
D2
D1
D0
A2:0
COMMENT
HX
X
Serial Data
Output
Serial Data Input
X
32-Bit Serial Mode
LH
Parallel Data
Input
Parallel Data
Input
Parallel Data
Input
Output
Address
Parallel Mode; D2:0 define the
command to be executed
LL
Parallel Data
Input
Parallel Data
Input
Parallel Data
Input
Output
Address
Parallel Mode; D2:0 define the Input
Channel
HA456
相关PDF资料 |
PDF描述 |
|---|---|
| HC5513BIM | IC SLIC DLC/FLC LP STDBY 22-DIP |
| HC55143IM | IC SLIC UNIVERSAL LP 32-PLCC |
| HC5515CMZ | IC SLIC ITU CO/PABX LP 28-PLCC |
| HC9P5504B-5ZX96 | IC SLIC EIA/ITU PABX 24-SOIC |
| HD3-6402R-9Z | IC UART CMOS 5V 2MHZ 40-DIP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HA456CMZ | 功能描述:模拟和数字交叉点 IC W/ANNEAL XPOINT 8X8 VID GAIN+1 44PLCC RoHS:否 制造商:Micrel 配置:2 x 2 封装 / 箱体:MLF-16 数据速率:10.7 Gbps 输入电平:CML, LVDS, LVPECL 输出电平:CML 电源电压-最大:3.6 V 电源电压-最小:2.375 V 最大工作温度:+ 85 C 最小工作温度:- 40 C 产品:Digital Crosspoint 封装:Tube |
| HA456CN | 制造商:Rochester Electronics LLC 功能描述:XPOINT 8X8 VIDEO GAIN+1 44MQFP COM - Bulk |
| HA456CP | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HA456EVAL1 | 功能描述:交换机 IC 开发工具 EVAL PLATFORM HA456 RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:USB Power Switches 工具用于评估:MAX4984E 工作电源电压:2.8 V to 5.5 V |
| HA457 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:95MHz, Low Power, AV = 2, 8 x 8 Video Crosspoint Switch |
发布紧急采购，3分钟左右您将得到回复。