- 您现在的位置：买卖IC网 > PDF目录296087 > HB288032MM1 FLASH 2.7V PROM CARD, XMA7 PDF资料下载
参数资料
| 型号： | HB288032MM1 |
| 元件分类： | PROM |
| 英文描述： | FLASH 2.7V PROM CARD, XMA7 |
| 封装： | CARD-7 |
| 文件页数： | 24/80页 |
| 文件大小： | 236K |
| 代理商： | HB288032MM1 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页当前第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页第69页第70页第71页第72页第73页第74页第75页第76页第77页第78页第79页第80页
HB288032MM1
30
Card identification mode
All the data communication in the card identification mode uses only the command line (CMD).
Idle state
(idle)
CMD0
CMD15
CMD1
Inactive state
Ready state
(ready)
CMD2
Indentification state
(ident)
CMD3
Stand-by state
(stby)
card wins bus
(ina)
from all states except (ina)
from all states in data-transfer mode
Power on
card looses bus
card is busy or
host omitted
voltage range
cards with non-compatible voltage range
data-transfer mode
card-indentification mode
MultiMediaCard State Diagram (Card Identification Mode)
The host starts the card identification process in open drain mode with the identification clock rate f
OD
(generated by a push pull driver stage). The open drain driver stages on the CMD line allow the parallel
card operation during card identification. After the bus is activated the host will request the cards to send
their valid operation conditions with the command SEND_OP_COND (CMD1). Since the bus is in open
drain mode, as long as there is more than one card with operating conditions restrictions, the host gets in
the response to the CMD1 a “wired or” operation condition restrictions of those cards. The host then must
pick a common denominator for operation and notify the application that cards with out of range
parameters (from the host perspective) are connected to the bus. Incompatible cards go into Inactive State
(refer to also Chapter “Operating Voltage Range Validation”). The busy bit in the CMD1 response can be
used by a card to tell the host that it is still working on its power-up/reset procedure (e.g. downloading the
register information from memory field) and is not ready yet for communication. In this case the host must
repeat CMD1 until the busy bit is cleared. After an operating mode is established, the host asks all cards
for their unique card identification (CID) number with the broadcast command ALL_SEND_CID (CMD2).
All not already identified cards (i.e. those which are in Ready State) simultaneously start sending their CID
numbers serially, while bit-wise monitoring their outgoing bitstream. Those cards, whose outgoing CID
相关PDF资料 |
PDF描述 |
|---|---|
| HB28A896IA1 | 448M X 16 FLASH 5V PROM CARD, XMA68 |
| HB56A232BW-6C | 2M X 32 FAST PAGE DRAM MODULE, 60 ns, SMA72 |
| HB56U432SB-5N | 4M X 32 EDO DRAM MODULE, 50 ns, SMA72 |
| HBCC-471J-02 | 1 ELEMENT, 470 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
| HBCC-1R2K-02 | 1 ELEMENT, 1.2 uH, FERRITE-CORE, GENERAL PURPOSE INDUCTOR |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HB288064A5 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288064A6 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:FLASH ATA Card |
| HB288064C5 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288064C6 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:CompactFlash⑩ |
| HB288064MM1 | 制造商:HITACHI 制造商全称:Hitachi Semiconductor 功能描述:MultiMediaCard 64 MByte |
发布紧急采购，3分钟左右您将得到回复。