- 您现在的位置：买卖IC网 > PDF目录10995 > HC55140IMZ (Intersil)IC SLIC UNIVERSAL LP 28-PLCC PDF资料下载
参数资料
| 型号： | HC55140IMZ |
| 厂商： | Intersil |
| 文件页数： | 13/36页 |
| 文件大小： | 0K |
| 描述： | IC SLIC UNIVERSAL LP 28-PLCC |
| 标准包装： | 37 |
| 系列： | UniSLIC14 |
| 功能： | 用户线路接口概念（SLIC） |
| 电路数： | 1 |
| 电源电压： | 4.75 V ~ 5.25 V |
| 电流 - 电源： | 2.25mA |
| 功率（瓦特）： | 1.5W |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-LCC（J 形引线） |
| 供应商设备封装： | 28-PLCC（11.51x11.51） |
| 包装： | 管件 |
| 包括： | 电池跟踪抗削顶失真，回路和接地键检测，振铃控制 |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页当前第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页
20
FN4659.13
June 1, 2006
SPM Pin
For optimum performance, the PC board interconnect the
SPM pin should be as short as possible. If pulses metering is
not being used, then this pin should be grounded as close to
the device pin as possible.
RLIM Pin
The current limiting resistor RLIM needs to be as close to the
RLIM pin as possible.
Layout of the 2-Wire Impedance Matching
Resistor ZT
Proper connection to the ZT pin is to have the external ZT
network as close to the device pin as possible.
The ZT pin is a high impedance pin that is used to set the
proper feedback for matching the impedance of the 2-wire
side. This will eliminate circuit board capacitance on this pin
to maintain the 2-wire return loss across frequency.
Digital Logic Inputs
Table 1 is the logic truth table for the 3V to 5V logic input
pins. A combination of the control pins C3, C2 and C1 select
1 of the possible 6 operating states. The 8th state listed is
Thermal Shutdown. Thermal Shutdown protection is invoked
if a fault condition on the tip or ring causes the junction
temperature of the die to exceed 175°C. A description of
each operating state and the control logic follows:
Open Circuit State (C3 = 0, C2 = 0, C1 = 0)
In this state, the tip and ring outputs are in a high impedance
condition (>1M
). No supervisory functions are available
and SHD and GKD outputs are at a TTL high level.
4-wire loopback testing can be performed in this state. With
the PTG pin floating, the signal on the VTX output is 180
o out
of phase and approximately 2 times the VRX input signal. If
the PTG pin is grounded, then the amplitude will be
approximately the same as its input and 180o out of phase.
Ringing State (C3 = 0, C2 = 0, C1 = 1)
In this state, the output of the ring relay driver pin (RRLY)
goes low (energizing the ring relay to connect the ringing
signal to the phone) if either of the following two conditions
are satisfied:
(1) The RSYNC_REV pin is grounded through a resistor -
This connection enables the RRLY pin to go low the instant
the ringing state is invoked, without any regard for the
ringing voltage (90VRMS -120VRMS) across the relay
contacts. The resistor (34.8k
to 70k) is required to limit
the current into the RSYNC_REV pin.
(2) A ring sync pulse is applied to the RSYNC_REV pin -
This connection enables the RRLY pin to go low at the
command of a ring sync pulse. A ring sync pulse should go
TABLE 1. DETECTOR STATES
STATE
C3
C2
C1
SLIC OPERATING STATE
ACTIVE DETECTOR
OUTPUT
SHD
GKD_ LVM
0
Open Circuit State
4 wire loopback test capability
HIGH
1
0
1
Ringing State
(Previous State cannot be Reverse
Active State)
Ring Trip Detector
HIGH
2
0
1
0
Forward Active State
Loop Current Detector
Ground Key Detector
3
0
1
Test Active State
Requires previous state to be in the
Forward Active state to determine the
On hook or Off hook status of the line.
On Hook Loopback Detector
LOW
Ground Key Detector
HIGH
Off Hook Loop Current Detector
LOW
Line Voltage Detector
4
1
0
Tip Open - Ground Start State
Ground Key Detector
5
1
0
1
Reserved
N/A
6
1
0
Reverse Active State
Loop Current Detector
Ground Key Detector
7
1
Test Reversal Active State
Requires previous state to be in the
Reverse Active state to determine the
On hook or Off hook status of the line.
On Hook Loop Current Detector
HIGH
Off Hook Loop Current Detector
LOW
Line Voltage Detector
8
X
Thermal Shutdown
LOW
HC55120, HC55121, HC55130, HC55140, HC55142, HC55143, HC55150
相关PDF资料 |
PDF描述 |
|---|---|
| MC9S08AC96MFGE | MCU 8BIT 96K FLASH 44-LQFP |
| HC55130IMZ | IC SLIC UNIVERSAL LP 28-PLCC |
| MC9S08AC96CLKE | MCU 96K FLASH 8K RAM 80-LQFP |
| HC55121IMZ | IC SLIC UNIVERSAL LP 28-PLCC |
| HC55120CMZ | IC SLIC UNIVERSAL LP 28-PLCC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HC55141 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC55141IM | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC55142 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC55142IB | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Low Power Universal SLIC Family |
| HC55142IBZ | 功能描述:电信线路管理 IC LW PWR SLIC POLV/MTRING 63DB RoHS:否 制造商:STMicroelectronics 产品:PHY 接口类型:UART 电源电压-最大:18 V 电源电压-最小:8 V 电源电流:30 mA 最大工作温度:+ 85 C 最小工作温度:- 40 C 安装风格:SMD/SMT 封装 / 箱体:VFQFPN-48 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。