参数资料
型号: HCPL-2730
英文描述: (264.18 k)
中文描述: (264.18十一)
文件页数: 2/12页
文件大小: 264K
代理商: HCPL-2730
10
Package Characteristics
Device
Parameter
Symbol HCPL- Min. Typ.* Max. Units
Test Conditions
Fig.
Note
Input-Output Momentary
VISO
2500
V rms
RH
≤ 50%,
4, 9
Withstand Voltage**
t = 1 min.,
Option 020
2730
5000
4, 10
2731
Resistance
RI-O
1012
VI-O = 500 VDC
4
(Input-Output)
RH
≤ 45%
Capacitance
CI-O
0.6
pF
f = 1 MHz
11
(Input-Output)
Input-Input Insulation
II-I
0.005
A
RH
≤ 45%
5
Leakage Current
VI-I = 500 VDC
Input-Input Insulation
RI-I
1011
5
Leakage Current
Capacitance
CI-I
2730
0.03
pF
5
(Input-Input)
2731
0730
0.25
0731
*All Typical values at T
A = 25°C unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output
continuous voltage rating. For the continuous voltage rating refer to the VDE 0884 Insulation Characteristics Table (if appli-
cable), your equipment level safety specification or Agilent Application Note 1074 entitled “Optocoupler Input-Output Endurance
Voltage.”
Notes:
1. Pin 5 should be the most negative
voltage at the detector side.
2. Each channel.
3. DC CURRENT TRANSFER RATIO
(CTR) is defined as the ratio of output
collector current, I
O, to the forward
LED input current, I
F, times 100%.
4. Device considered a two-terminal
device: pins 1, 2, 3, and 4 shorted
together, and pins 5, 6, 7, and 8
shorted together.
5. Measured between pins 1 and 2
shorted together, and pins 3 and 4
shorted together.
6. Common mode transient immunity in a
Logic High level is the maximum
tolerable (positive) dV
CM/dt of the
TA = 25°C
common mode pulse, V
CM, to assure
that the output will remain in a Logic
High state (i.e., V
O > 2.0 V). Common
mode transient immunity in a Logic
Low level is the maximum tolerable
(negative) dV
CM/dt of the common
mode pulse, V
CM, to assure that the
output will remain in a Logic Low state
(i.e., V
O < 0.8 V).
7. In applications where dV/dt may
exceed 50,000 V/
s (such as static
discharge) a series resistor, R
CC,
should be included to protect the
detector IC from destructively high
surge currents. The recommended
value is R
CC = 110 .
8. Use of a 0.1
F bypass capacitor
connected between pins 5 and 8
adjacent to the device is
recommended.
9. In accordance with UL 1577, each
optocoupler is proof tested by
applying an insulation test voltage
> 3000 V rms for 1 second (leakage
detection current limit, I
I-O < 5 A).
10. In accordance with UL 1577, each
optocoupler is proof tested by
applying an insulation test voltage
> 6000 V rms for 1 second (leakage
detection current limit, I
I-O < 5 A).
11. Measured between the LED anode and
cathode shorted together and pins 5
through 8 shorted together.
12. Derate linearly above 65
°C free-air
temperature at a rate of 2.3 mW/
°C for
the SO-8 package.
相关PDF资料
PDF描述
HCPL-4504 NPN-OUTPUT DC-INPUT OPTOCOUPLER
HCPL-4506 SCHMITT-TRIGGER-OUTPUT OPTOCOUPLER
HCPL-5201 LOGIC-GATE-OUTPUT OPTOCOUPLER
HCPL-5401 SCHMITT-TRIGGER-OUTPUT OPTOCOUPLER
HCPL-540K SCHMITT-TRIGGER-OUTPUT OPTOCOUPLER
相关代理商/技术参数
参数描述
HCPL-2730#020 功能描述:高速光耦合器 100kBd 2Ch 0.5mA RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
HCPL-2730#300 功能描述:高速光耦合器 100kBd 2Ch 0.5mA RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
HCPL-2730#320 功能描述:高速光耦合器 100kBd 2Ch 0.5mA RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
HCPL-2730#500 功能描述:高速光耦合器 100kBd 2Ch 0.5mA RoHS:否 制造商:Avago Technologies 电流传递比: 最大波特率: 最大正向二极管电压:1.75 V 最大反向二极管电压:5 V 最大功率耗散:40 mW 最大工作温度:+125 C 最小工作温度:- 40 C 封装 / 箱体:SOIC-5 封装:Tube
HCPL2730 制造商:Fairchild Semiconductor Corporation 功能描述:OPTOCOUPLER 制造商:Fairchild Semiconductor Corporation 功能描述:OPTOCOUPLER, DARLINGTON, 2500VRMS