- 您现在的位置：买卖IC网 > PDF目录296089 > HCPL-5150-300 0.5 Amp Output Current IGBT Gate Drive Optocoupler PDF资料下载
参数资料
| 型号： | HCPL-5150-300 |
| 英文描述： | 0.5 Amp Output Current IGBT Gate Drive Optocoupler |
| 中文描述： | 0.5安培输出电流IGBT栅极驱动光电耦合器 |
| 文件页数： | 5/16页 |
| 文件大小： | 193K |
| 代理商： | HCPL-5150-300 |
13
Figure 27. Energy Dissipated in the HCPL-5150
for Each IGBT Switching Cycle
LED Drive Circuit Considerations for
Ultra High CMR Performance.
Without a detector shield, the
dominant cause of optocoupler
CMR failure is capacitive
coupling from the input side of
the optocoupler, through the
package, to the detector IC as
shown in Figure 28.
The HCPL- 5150 improves CMR
performance by using a detector
IC with an optically transparent
Faraday shield, which diverts
the capacitively coupled current
away from the sensitive IC
circuitry. However, this shield
does not eliminate the
capacitive coupling between the
LED and optocoupler pins 5- 8
as shown in Figure 29. This
capacitive coupling causes
perturbations in the LED
current during common mode
transients and becomes the
major source of CMR failures
for a shielded optocoupler. The
main design objective of a high
CMR LED drive circuit becomes
keeping the LED in the proper
state (on or off) during common
mode transients. For example,
the recommended application
circuit, (Figure 25) can achieve
10 kV/
s CMR while minimizing
component complexity.
Techniques to keep the LED in
the proper state are discussed
in the next two sections.
Figure 28. Optocoupler Input to Output Capaci-
tance Model for Unshielded Optocouplers
Figure 29. Optocoupler Input to Output Capaci-
tance Model for Shielded Optocouplers
Figure 26. Typical Application Circuit with Negative IGBT Gate Drive
+ HVDC
3-PHASE
AC
- HVDC
0.1 F
V CC = 15 V
1
3
+
2
4
8
6
7
5
Rg
Q1
Q2
V EE = -5 V
+
270
+5 V
CONTROL
INPUT
74XXX
OPEN
COLLECTOR
_
PE Parameter Description
IF
LED Current
VF
LED On Voltage
Duty Cycle
Maximum LED
Duty Cycle
PO Parameter Description
ICC
Supply Current
VCC
Positive Supply
Voltage
VEE
Negative Supply
Voltage
ESW (Rg, Qg)
Energy Dissipation in
the HCPL-5150 for
each IGBT Switching
Cycle (See Figure 27)
f
Switching Frequency
Esw
-
ENERGY
PER
SWITCHING
CYCLE
-
J
0
Rg - GATE RESISTANCE -
100
3
20
7
40
2
60
80
6
Qg = 100 nC
Qg = 250 nC
Qg = 500 nC
5
4
1
VCC = 19 V
VEE = -9 V
1
3
2
4
8
6
7
5
CLEDP
CLEDN
1
3
2
4
8
6
7
5
CLEDP
CLEDN
SHIELD
CLEDO1
CLEDO2
相关PDF资料 |
PDF描述 |
|---|---|
| HCPL-5151 | 0.5 Amp Output Current IGBT Gate Drive Optocoupler |
| HCPL-523K#300 | 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 5 Mbps |
| HCPL-7721#500 | 1 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 25 Mbps |
| HCPL0661R2 | 2 CHANNEL LOGIC OUTPUT OPTOCOUPLER, 10 Mbps |
| HD10181F | 10K SERIES, 4-BIT ARITHMETIC LOGIC UNIT, CQFP24 |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCPL-5151 | 功能描述:逻辑输出光电耦合器 0.5A IGBT Gate Drive Hermetically sealed RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube |
| HCPL-5151#100 | 制造商:Avago Technologies 功能描述:OPTOCOUPL LOGIC-OUT PUSH-PULL DC-IN 1CH 8PDIP SMD - Bulk |
| HCPL-5151#200 | 制造商:Avago Technologies 功能描述:OPTOCOUPL LOGIC-OUT PUSH-PULL DC-IN 1CH 8PDIP - Bulk |
| HCPL-5151#300 | 制造商:Avago Technologies 功能描述:OPTOCOUPL LOGIC-OUT PUSH-PULL DC-IN 1CH 8PDIP SMD - Bulk |
| HCPL-5151-100 | 功能描述:逻辑输出光电耦合器 0.5A IGBT Gate Drive Hermetically sealed RoHS:否 制造商:Fairchild Semiconductor 绝缘电压:4243 Vrms 输出类型:Push-Pull 最大传播延迟时间:500 ns 最大正向二极管电压: 最大反向二极管电压: 最大正向二极管电流: 最大连续输出电流:2.5 A 最大功率耗散:100 mW 最大工作温度:+ 100 C 最小工作温度:- 40 C 封装 / 箱体:SO-16 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。