- 您现在的位置：买卖IC网 > PDF目录371778 > HCPL-7510-060 Isolated Linear Sensing IC PDF资料下载
参数资料
| 型号： | HCPL-7510-060 |
| 英文描述： | Isolated Linear Sensing IC |
| 中文描述： | 隔离线性传感IC |
| 文件页数： | 15/16页 |
| 文件大小： | 117K |
| 代理商： | HCPL-7510-060 |
15
FREQUENTLY ASKED QUESTIONS ABOUT THE HCPL-7510
1. THE BASICS
1.1: Why should I use the HCPL-7510 for sensing current when Hall-effect sensors are available which don’t need an
isolated supply voltage
Available in an auto-insertable, 8-pin DIP package, the HCPL-7510 is smaller than and has better
linearity, offset vs. temperature and Common Mode Rejection (CMR) performance than most Hall-
effect sensors. Additionally, often the required input-side power supply can be derived from the
same supply that powers the gate-drive optocoupler.
2. SENSE RESISTOR AND INPUT FILTER
2.1: Where do I get 10 m
resistors I have never seen one that low.
Although less common than values above 10
, there are quite a few manufacturers of resistors
suitable for measuring currents up to 50 A when combined with the HCPL-7510. Example product
information may be found at Dale’s web site (http://www.vishay.com/vishay/dale) and Isotek’s web
site (http://www.isotekcorp.com) and Iwaki Musen Kenkyusho’s website (http://
www.iwakimusen.co.jp) and Micron Electric’s website (http://www.micron-e.co.jp).
2.2: Should I connect both inputs across the sense resistor instead of grounding VIN- directly to pin 4
This is not necessary, but it will work. If you do, be sure to use an RC filter on both pin 2 (VIN+)
and pin 3 (VIN-) to limit the input voltage at both pads.
2.3: Do I really need an RC filter on the input What is it for Are other values of R and C okay
The input anti-aliasing filter (R=39
, C=0.01 μF) shown in the typical application circuit is
recommended for filtering fast switching voltage transients from the input signal.
(This helps to attenuate higher signal frequencies which could otherwise alias with the input
sampling rate and cause higher input offset voltage.)
Some issues to keep in mind using different filter resistors or capacitors are:
1. (Filter resistor:) The equivalent input resistance for HCPL-7510 is around 700 k
. It is
therefore best to ensure that the filter resistance is not a significant percentage of this value;
otherwise the offset voltage will be increased through the resistor divider effect. [As an
example, if Rfilt = 5.5 k
, then VOS = (Vin * 1%) = 2 mV for a maximum 200 mV input and
VOS will vary with respect to Vin.]
2. The input bandwidth is changed as a result of this different R-C filter configuration. In fact this
is one of the main reasons for changing the input-filter R-C time constant.
3. (Filter capacitance:) The input capacitance of the HCPL-7510 is approximately 1.5 pF. For
proper
operation the switching input-side sampling capacitors must be charged from a
relatively fixed (low impedance) voltage source. Therefore, if a filter capacitor is used it is best
for this capacitor to be a few orders of magnitude greater than the CINPUT (A value of at least
100 pF works well.)
2.4: How do I ensure that the HCPL-7510 is not destroyed as a result of short circuit conditions which
voltage drops across the sense resistor that exceed the ratings of the HCPL-7510’s inputs
Select the sense resistor so that it will have less than 5 V drop when short circuits occur. The
only other requirement is to shut down the drive before the sense resistor is damaged or its
solder joints melt. This ensures that the input of the HCPL-7510 can not be damaged by sense
resistors going open-circuit.
cause
3. ISOLATION AND INSULATION
3.1: How many volts will the HCPL-7510 withstand
The momentary (1 minute) withstand voltage is 3750 V rms per UL 1577 and CSA Component
Acceptance Notice #5.
相关PDF资料 |
PDF描述 |
|---|---|
| HCPL-7510-060E | Isolated Linear Sensing IC |
| HCPL-7510-300 | Isolated Linear Sensing IC |
| HCPL-7510-300E | Isolated Linear Sensing IC |
| HCPL-7510-500 | Isolated Linear Sensing IC |
| HCPL-7800A-500 | High CMR Isolation Amplifiers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCPL-7510-060E | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-300 | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-300E | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-360 | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-360E | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。