- 您现在的位置：买卖IC网 > PDF目录371778 > HCPL-7510-060E Isolated Linear Sensing IC PDF资料下载
参数资料
| 型号： | HCPL-7510-060E |
| 英文描述： | Isolated Linear Sensing IC |
| 中文描述： | 隔离线性传感IC |
| 文件页数： | 8/16页 |
| 文件大小： | 117K |
| 代理商： | HCPL-7510-060E |
8
Package Characteristics
Parameter
Symbol
Min.
Typ.
Max.
Units
Test Conditions
Fig.
Note
Input-Output Momentary
Withstand Voltage
V
ISO
3750
V
rms
T
A
= 25°C, RH < 50%
6
Input-Output Resistance
R
I-O
>10
9
V
I-O
= 500 V
Input-Output Capacitance
C
I-O
1.4
pF
Freq = 1 MHz
Notes:
General Note: Typical values were taken from a sample of nominal units operating at nominal conditions (V
DD1
= V
DD2
= 5 V, V
REF
= 4.0 V, Temperature =
25°C) unless otherwise stated. Nominal plots shown from Figure 1 to 11 represented the drift of these nominal units from their nominal operating
conditions.
1. Input Offset Voltage is defined as the DC Input Voltage required to obtain an output voltage of V
REF
/2.
2. Gain is defined as the slope of the best-fit line of the output voltage vs. the differential input voltage (V
IN+
- V
IN-
) over the specified input range. Gain
is derived from V
REF
/512 mV; e.g. V
REF
= 5.0, gain will be 9.77 V/V.
3. Nonlinearity is defined as half of the peak-to-peak output deviation from the best-fit gain line, expressed as a percentage of the full-scale output
voltage range.
4. NL
200
is the nonlinearity specified over an input voltage range of ±200 mV.
5. NL
100
is the nonlinearity specified over an input voltage range of ±100 mV.
6. In accordance with UL1577, each optocoupler is proof tested by applying an insulation test voltage 4500 Vrms for 1 second (leakage detection current
limit, I
I-O
< 5 μA). This test is performed before the 100% production test for the partial discharge (method b) shown in
IEC/EN/DIN EN 60747-5-2 Insulation Characteristic Table, if applicable.
7. CMRR is defined as the ratio of the differential signal gain (signal applied differentially between pins 2 and 3) to the common-mode gain (input pins
tied together and the signal applied to both inputs at the same time), expressed in dB.
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified.
Parameter
Symbol Min.
Typ.
Max.
Units
Test Conditions
Fig. Note
V
IN
to V
OUT
Signal Delay (50 – 10%)
V
IN
to V
OUT
Signal Delay (50 – 50%)
V
IN
to V
OUT
Signal Delay (50 – 90%)
V
OUT
Rise Time (10 – 90%)
V
OUT
Fall Time (10 – 90%)
V
OUT
Bandwidth (-3 dB)
V
OUT
Noise
Common Mode Transient
Immunity
t
PD10
t
PD50
t
PD90
t
R
t
F
BW
2.2
4
μs
V
IN+
= 0 mV to 200 mV step
13
3.4
5
μs
5.2
9.9
μs
3.0
7
μs
3.2
7
μs
50
100
kHz
V
IN+
= 200 mV
pk-pk
mVrms V
IN+
= 0 V
kV/μs
T
A
= 25°C, V
CM
= 1000 V
14
N
OUT
CMTI
31.5
10
15
15
相关PDF资料 |
PDF描述 |
|---|---|
| HCPL-7510-300 | Isolated Linear Sensing IC |
| HCPL-7510-300E | Isolated Linear Sensing IC |
| HCPL-7510-500 | Isolated Linear Sensing IC |
| HCPL-7800A-500 | High CMR Isolation Amplifiers |
| HCPL-7800B-300 | High CMR Isolation Amplifiers |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCPL-7510-300 | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-300E | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-360 | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-360E | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
| HCPL-7510-500 | 功能描述:隔离放大器 4.5 - 5.5 SV +/-3% RoHS:否 制造商:Texas Instruments 输入补偿电压:1.5 mV 共模抑制比（最小值）:95 dB 带宽:60 KHz 工作电源电压:3.3 V 电源电流:8 mA 工作温度范围:- 40 C to + 105 C 安装风格:SMD/SMT 封装 / 箱体:SOP-8 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。