参数资料
型号: HCS473SLQTP
厂商: Microchip Technology Inc.
英文描述: Code Hopping Encoder and Transponder
中文描述: 跳码编码器和转发器
文件页数: 10/68页
文件大小: 1629K
代理商: HCS473SLQTP
HCS473
DS40035C-page 8
Preliminary
2002 Microchip Technology Inc.
2.3.3
TRANSPONDER INTERFACE
The transponder interface on the HCS473 consists of
the following:
The internal transponder circuitry has separate
power supply (V
DDT
) and ground (V
SST
) connec-
tions.
- The V
DDT
pin supplies power to the transpon-
der circuitry and also outputs a regulated volt-
age if the LCX antenna input is receiving a
strong signal; transponder is placed in a
strong LF field.
- The V
SST
pin supplies the ground reference
to the transponder circuitry and must be con-
nected to the V
SS
pin.
LF input amplifier and envelope detector to detect
and shape the incoming low frequency excitation
signal.
Three sensitive transponder inputs with over-volt-
age protection (LCX, LCY, LCZ).
Incoming LF energy rectification and regulation on
the LCX input to supplement the supply voltage in
low-battery transponder instances.
10V zener input protection from excessive
antenna voltage resulting when proximate to very
strong magnetic fields.
LCCOM pin used to bias the transponder reso-
nant circuits for best sensitivity.
LF antenna clamping transistors for inductive
responses back to the transponder reader. The
antenna ends are shorted together, ‘clamped’,
dissipating the oscillatory energy. The reader
detects this as a momentary load on its excitation
antenna.
Damping transistors to increase LF communica-
tion reliability when using high Q-factor LC anten-
nae.
The LCCOM pin functions to bias the LCX, LCY, and
LCZ AGC amplifier inputs. The amplifier gain control
sets the optimum level of amplification in respect to the
incoming signal strength. The signal then passes
through an envelope detector before interpretation in
the logic circuit.
A block diagram of the transponder circuit is shown in
Figure 2-8.
FIGURE 2-8:
HCS473 TRANSPONDER
CIRCUIT
2.3.4
INTERNAL EEPROM
The HCS473 has an on-board non-volatile EEPROM
which is used to store:
configuration options
- encryption keys
- serial number
- vehicle ID’s
- baud rates
- ... see Section 3.1.4 and Section 3.2.1
64 bits of user memory
synchronization counter.
All options are programmable during production, but
many of the security related options are programmable
only during production and are further read protected.
The user area allows storage of general purpose infor-
mation and is accessible only through the transponder
communication path.
During every EEPROM write, the device ensures that
the internal programming voltage is at an acceptable
level prior to performing the EEPROM write.
Damp/Clamp
Control
Rectifier/
Regulator
V
CCT
Noise
Filter
Signal In
LCX
LCY
LCZ
LCCOM
相关PDF资料
PDF描述
HCS473SLROM Code Hopping Encoder and Transponder
HCS473SLSQTP Code Hopping Encoder and Transponder
HCS509 KEELOQ Code Hopping Encoder Product Brief*(KeeLoq 译码器,是NTQ109和NTQ106的替代品)
HCS573KMSR Radiation Hardened Octal Transparent Latch, Three-State
HCS573D Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control
相关代理商/技术参数
参数描述
HCS473-SLQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473SLROM 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473-SLROM 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473SLSQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473-SLSQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder