- 您现在的位置：买卖IC网 > PDF目录371784 > HCS473SLROM (Microchip Technology Inc.) Code Hopping Encoder and Transponder PDF资料下载
参数资料
| 型号： | HCS473SLROM |
| 厂商： | Microchip Technology Inc. |
| 英文描述： | Code Hopping Encoder and Transponder |
| 中文描述： | 跳码编码器和转发器 |
| 文件页数： | 42/68页 |
| 文件大小： | 1629K |
| 代理商： | HCS473SLROM |
第1页第2页第3页第4页第5页第6页第7页第8页第9页第10页第11页第12页第13页第14页第15页第16页第17页第18页第19页第20页第21页第22页第23页第24页第25页第26页第27页第28页第29页第30页第31页第32页第33页第34页第35页第36页第37页第38页第39页第40页第41页当前第42页第43页第44页第45页第46页第47页第48页第49页第50页第51页第52页第53页第54页第55页第56页第57页第58页第59页第60页第61页第62页第63页第64页第65页第66页第67页第68页
HCS473
DS40035C-page 40
Preliminary
2002 Microchip Technology Inc.
FIGURE 5-2:
TYPICAL DECODER
OPERATION
5.3
Synchronization with Decoder
The
synchronization technique (Figure 5-3) which does not
require the calculation and storage of future codes. If
the stored counter value for that particular transmitter
and the counter value that was just decrypted are
within a window of 16 codes, the counter is stored and
the command is executed. If the counter value was not
within the single operation window, but is within the
double operation window of 32K codes (when using a
16-bit counter), the transmitted synchronization value
is stored in temporary location and it goes back to wait-
ing for another transmission.
technology
features
a
sophisticated
When the next valid transmission is received, it will
check the new value with the one in temporary storage.
If the two values are sequential, it is assumed that the
counter had just gotten out of the single operation ‘win-
dow’. Since it is now back in sync, the new synchroni-
zation value is stored and the command executed.
If a transmitter has somehow gotten out of the double
operation window, the transmitter will not work and
must be relearned. Since the entire window rotates
after each valid transmission, codes that have been
used are part of the ‘blocked’ (32K) codes and are no
longer valid. This eliminates the possibility of grabbing
a previous code and retransmitting to gain entry.
FIGURE 5-3:
SYNCHRONIZATION
WINDOW (16-BIT
COUNTER)
5.4
Inductive Communication
Communication between a base station and a HCS473
transponder occurs via magnetic coupling between the
transponder coil and base station coil. The base station
coil forms part of a series RLC circuit. The base station
communicates to the transponder by switching the 125
kHz signal to the series RLC circuit on and off. Thus,
the base station magnetic field is switched on and off.
The transponder coil is connected in parallel with a res-
onating capacitor (125 kHz) and the HCS473.
When the transponder is brought into the base station
magnetic field, it magnetically couples with this field
and draws energy from it. This loading effect can be
observed as a decrease in voltage across the base sta-
tion resonating capacitor. The K
EE
L
OQ
transponder
communicates to the base station by “shorting out” its
parallel LC circuit. This detunes the transponder and
removes the load, which is observed as an increase in
voltage across the base station resonating capacitor.
The base station capacitor voltage is the input to the
base station AM demodulator circuit. The demodulator
extracts the transponder data for further processing by
the base station software.
Transmission
Received
Does
Serial Number
Match
Decrypt Transmission
Is
Decryption
Valid
Is
Counter
Within 16
Is
Counter
Within 32K
Update
Counter
Execute
Command
and
Save Counter
in Temp Location
Start
No
No
No
No
Yes
Yes
Yes
Yes
Yes
No
No
Note:
The synchronization method described in
this section is only a typical implementation
and because it is usually implemented in
firmware, it can be altered to fit the needs
of a particular system
Blocked
(32K Codes)
Entire Window
rotates to eliminate
use of previously
used codes
Current
Position
Double
Operation
(32K Codes)
Single Operation
Window (16 Codes)
相关PDF资料 |
PDF描述 |
|---|---|
| HCS473SLSQTP | Code Hopping Encoder and Transponder |
| HCS509 | KEELOQ Code Hopping Encoder Product Brief*(KeeLoq 译码器，是NTQ109和NTQ106的替代品) |
| HCS573KMSR | Radiation Hardened Octal Transparent Latch, Three-State |
| HCS573D | Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control |
| HCS573DMSR | Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HCS473-SLROM | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473SLSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473-SLSQTP | 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder |
| HCS473T/SL | 功能描述:编码器、解码器、复用器和解复用器 w/ Passive Entry RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
| HCS473T-I/SL | 功能描述:编码器、解码器、复用器和解复用器 w/ Passive Entry RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量（输入/输出）:2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray |
发布紧急采购，3分钟左右您将得到回复。