参数资料
型号: HCS473SLSQTP
厂商: Microchip Technology Inc.
英文描述: Code Hopping Encoder and Transponder
中文描述: 跳码编码器和转发器
文件页数: 20/68页
文件大小: 1629K
代理商: HCS473SLSQTP
HCS473
DS40035C-page 18
Preliminary
2002 Microchip Technology Inc.
FIGURE 3-8:
LED OPERATION
3.1.6
CYCLE REDUNDANCY CHECK
(CRC)
The decoder can use the CRC bits to check the data
integrity before processing begins. The CRC is calcu-
lated on the previously transmitted bits (Figure 3-2),
detecting all single bit and 66% of all double bit errors.
EQUATION 3-1:
CRC CALCULATION
and
with
and Di
n
the nth transmission bit 0
n
64
3.1.7
COUNTER OVERFLOW BITS
(OVR1, OVR0)
The Counter Overflow Bits may be utilized to increase
the 16-bit synchronization counter range from the nom-
inal 65,535 to 131,070 or 196,605. The bits do not exist
when the device is configured for 20-bit counter opera-
tion.
The bits must be programmed during production as ‘1’s
to be utilized. OVR0 is cleared the first time the syn-
chronization counter wraps from FFFFh to 0000h.
OVR1 is cleared the second time the synchronization
counter wraps to zero. The two bits remain at ‘0’ after
all subsequent counter wraps.
3.1.8
DISCRIMINATION VALUE (DISC)
The Discrimination Value is typically used by the
decoder in a post-decryption check. It may be any
value, but in a typical system it will be programmed
equal to the Least Significant bits of the serial number.
The discrimination bits are part of the information that
form the encrypted portion of the transmission
(Figure 3-2). After the receiver has decrypted a trans-
mission, the discrimination bits are checked against the
receiver’s stored value to verify that the decryption pro-
cess was valid; appropriate decryption key was used. If
the discrimination value was programmed as the LSb’s
of the serial number then it may merely be compared to
the respective bits of the received serial number.
The discrimination bit field size varies with the counter
select (CNTSEL) option (Figure 3-2).
3.2
Transponder Mode
The HCS473’s Transponder mode allows it to function
as a bi-directional communication transponder. Com-
mands are received on the LC pins, responses may be
returned on either the LC pins or DATA pin for short
range LF or long range RF responses, respectively.
Transponder mode capabilities include:
A bi-directional challenge and response sequence
for IFF validation.
Read selected EEPROM areas.
Write selected EEPROM areas.
Request a code hopping transmission.
Proximity Activation of a code hopping transmis-
sion.
Address an individual transponder when multiple
units are within the LF field; device selection for
anticollision communication purposes.
SWITCH Sx
LED -
DATA
T
LEDON
T
LEDOFF
Code Word
Code Word
Code Word
T
LEDON
V
DD
>V
LOWSEL
(good battery)
LED -
V
DD
V
LOWSEL
(flat battery)
Note:
See Section 4.0, Programming Specs, for
information on programming OVR bits.
CRC 1
n
1
+
CRC 0
n
Di
n
=
CRC 0
n
1
+
CRC 0
n
Di
n
(
)
CRC 1
n
=
CRC 1 0
]
0
0
=
相关PDF资料
PDF描述
HCS509 KEELOQ Code Hopping Encoder Product Brief*(KeeLoq 译码器,是NTQ109和NTQ106的替代品)
HCS573KMSR Radiation Hardened Octal Transparent Latch, Three-State
HCS573D Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control
HCS573DMSR Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control
HCS573K Low-Voltage, Dual Hot-Swap Controllers with Independent On/Off Control
相关代理商/技术参数
参数描述
HCS473-SLSQTP 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Code Hopping Encoder and Transponder
HCS473T/SL 功能描述:编码器、解码器、复用器和解复用器 w/ Passive Entry RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量(输入/输出):2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray
HCS473T-I/SL 功能描述:编码器、解码器、复用器和解复用器 w/ Passive Entry RoHS:否 制造商:Micrel 产品:Multiplexers 逻辑系列:CMOS 位数: 线路数量(输入/输出):2 / 12 传播延迟时间:350 ps, 400 ps 电源电压-最大:2.625 V, 3.6 V 电源电压-最小:2.375 V, 3 V 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:QFN-44 封装:Tray
HCS4870C 制造商:Power-One 功能描述:POWER SUPPLY
HCS500 制造商:MICROCHIP 制造商全称:Microchip Technology 功能描述:Memory Programming Specification