参数资料
| 型号： | HHS60ZD-NTS1 |
| 厂商： | Power-One |
| 文件页数： | 10/12页 |
| 文件大小： | 0K |
| 描述： | DC/DC HALF BRICK |
| 标准包装： | 12 |
| 系列： | * |
HHS60 DC-DC Series Data Sheet
48VDC Input, 60 Amp Half-Brick Converter
Optional Positive-Trim (–T, P/N suffix)
increase shall not exceed the limits defined within the
“ Features ” section above.
The trim feature allows the user to adjust the output
voltage from its nominal value.
The HHS60 positive-trim (-T) models trim up with a
resistor from the Trim (#7) pin to the +Sense (#8) pin
and trims down with a resistor from the Trim pin to
4.
Either Rup or Rdown should be used to adjust the output
voltage according to the equations above. If both Rup and
Rdown are used simultaneously, they will form a resistive
divider and the equations above will not apply
the –Sense (#6) pin as shown in the Figure 17.
Figure 17 . HHS60 Series Positive Trim Schematic
The equations below determine the trim resistor
value required to achieve a Δ V change in the output
voltage.
100
R trim-dn = (-------- - 2) k Ω
Δ %
Vo*(100+ Δ %) (100+2* Δ %)
R trim-up = (-------------------- - ------------------) k Ω
1.225* Δ % Δ %
Safety Considerations
The HHS60 Series converters feature 1500 VDC
isolation from input to output. The input to output
resistance is greater than 10M ? . These converters
are provided with Basic insulation between input and
output circuits according to all IEC60950 based
standards. Nevertheless, if the system using the
converter needs to receive safety agency approval,
certain rules must be followed in the design of the
system. In particular, all of the creepage and
clearance requirements of the end-use safety
requirements must be observed. These documents
include UL60950 - CSA60950-00 and EN60950,
although other or additional requirements may be
needed for specific applications.
The HHS60 Series converters have no internal fuse.
An external fuse must be provided to protect the
system from catastrophic failure, as illustrated in
figure 15. Refer to the “Input Fuse Selection for
DC/DC converters” application note on www.power-
one.com for proper selection of the input fuse. Both
input traces and the chassis ground trace (if
applicable) must be capable of conducting a current
of 1.5 times the value of the fuse without opening.
The fuse must not be placed in the grounded input
line, if any.
In order for the output of the HHS60 Series converter
to be considered as SELV (Safety Extra Low
Voltage) or TNV-1, according to all IEC60950 based
standards, one of the following requirements must be
met in the system design:
where Δ V% is the output voltage change expressed
in percent of the nominal output voltage, Vout.
Notes:
1. When the output voltage is trimmed up, the output power
from the converter must not exceed its maximum rating. The
power is determined by measuring the output voltage on the
output pins, and multiplying it by the output current.
?
?
If the voltage source feeding the module is SELV
or TNV-2, the output of the converter may be
grounded or ungrounded.
If the voltage source feeding the module is ELV,
the output of the converter may be considered
SELV only if the output is grounded per the
2.
In order to avoid creating apparent load regulation
degradation, it is important that the trim resistors are
requirements of the standard.
connected directly to the remote sense pins, and not to the
load or to traces going to the load.
?
If the voltage source feeding the module is a
Hazardous Voltage Secondary Circuit, the
3.
The output voltage increase can be accomplished by either
the trim or by the remote sense or by the combination of
both. In any case the absolute maximum output voltage
voltage source feeding the module must be
provided with at least Basic insulation between
the source to the converter and any hazardous
JUN 06, 2006 revised to JUL 25, 2006
Page 10 of 12
www.power-one.com
相关PDF资料 |
PDF描述 |
|---|---|
| OSTEM19A150 | CONN TERM BLOCK 19POS 7.5MM |
| OSTVH105152 | TERM BLOCK PLUG 5.08MM 10POS |
| OSTTS22315A | TERM BLOCK PLUG 3.81MM 22POS |
| OSTTS22115A | TERM BLOCK PLUG 3.50MM 22POS |
| OSTVM197550 | TERM BLOCK PLUG 5.00MM 19POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HHS60ZE | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:HHS60 Series . 60A Half-Brick DC/DC Converter 48V Input 3.3V, 2.5V, 1,8V, 1.5V, 1.2V Outputs |
| HHS60ZE-NT | 功能描述:CONV DC-DC 48V IN 3.3V OUT 198W RoHS:否 类别:电源 - 板载 >> DC DC Converters 系列:HHS 标准包装:15 系列:Econoline REC5 类型:隔离 输出数:2 电压 - 输入（最小）:18V 电压 - 输入（最大）:72V Voltage - Output 1:15V Voltage - Output 2:-15V Voltage - Output 3:- 电流 - 输出（最大）:170mA，170mA 电源（瓦） - 制造商系列:5W 电压 - 隔离:2kV（2000V） 特点:- 安装类型:表面贴装 封装/外壳:24-DIP SMD 模块（18 引线） 尺寸/尺寸:1.26" L x 0.78" W x 0.44" H（32.0mm x 19.9mm x 11.2mm） 包装:管件 工作温度:-40°C ~ 75°C 效率:85% 电源（瓦特）- 最大:5W 其它名称:10010755 |
| HHS60ZE-NT8S1 | 制造商:Power-One 功能描述: |
| HHS60ZE-NT9 | 功能描述:DC/DC转换器 RoHS:否 制造商:Murata 产品: 输出功率: 输入电压范围:3.6 V to 5.5 V 输入电压（标称）: 输出端数量:1 输出电压（通道 1）:3.3 V 输出电流（通道 1）:600 mA 输出电压（通道 2）: 输出电流（通道 2）: 安装风格:SMD/SMT 封装 / 箱体尺寸: |
| HHS60ZY | 制造商:POWER-ONE 制造商全称:Power-One 功能描述:HHS60 Series . 60A Half-Brick DC/DC Converter 48V Input 3.3V, 2.5V, 1,8V, 1.5V, 1.2V Outputs |
发布紧急采购，3分钟左右您将得到回复。