- 您现在的位置：买卖IC网 > PDF目录371811 > HI-574 (Intersil Corporation) Complete, 12-Bit A/D Converters with Microprocessor Interface PDF资料下载
参数资料
| 型号： | HI-574 |
| 厂商： | Intersil Corporation |
| 元件分类： | 串行ADC |
| 英文描述： | Complete, 12-Bit A/D Converters with Microprocessor Interface |
| 中文描述： | 完成后，12位A / D转换器与微处理器接口 |
| 文件页数： | 10/18页 |
| 文件大小： | 200K |
| 代理商： | HI-574 |
6-961
Definitions of Specifications
Linearity Error
Linearity error refers to the deviation of each individual code
from a line drawn from “zero” through “full scale”. The point
used as “zero” occurs
1
/
2
LSB (1.22mV for 10V span) before
the first code transition (all zeros to only the LSB “on”). “Full
scale” is defined as a level 1
1
/
2
LSB beyond the last code tran-
sition (to all ones). The deviation of a code from the true straight
line is measured from the middle of each particular code.
The HI-X74(A)K and L grades are guaranteed for maximum
nonlinearity of
±
1
/
2
LSB. For these grades, this means that an
analog value which falls exactly in the center of a given code
width will result in the correct digital output code. Values nearer
the upper or lower transition of the code width may produce the
next upper or lower digital output code. The HI-X74(A)J is
guaranteed to
±
1 LSB max error. For this grade, an analog
value which falls within a given code width will result in either
the correct code for that region or either adjacent one.
Note that the linearity error is not user-adjustable.
Differential Linearity Error (No Missing Codes)
A specification which guarantees no missing codes requires
that every code combination appear in a monotonic increas-
ing sequence as the analog input level is increased. Thus
every code must have a finite width. For the HI-X74(A)K and L
grades, which guarantee no missing codes to 12-bit resolu-
tion, all 4096 codes must be present over the entire operating
temperature ranges. The HI-X74(A)J grade guarantees no
missing codes to 11-bit resolution over temperature; this
means that all code combinations of the upper 11 bits must be
present; in practice very few of the 12-bit codes are missing.
Unipolar Offset
The first transition should occur at a level
1
/
2
LSB above analog
common. Unipolar offset is defined as the deviation of the
actual transition from that point. This offset can be adjusted as
discussed on the following pages. The unipolar offset tempera-
ture coefficient specifies the maximum change of the transition
point over temperature, with or without external adjustment.
Bipolar Offset
Similarly, in the bipolar mode, the major carry transition
(0111 1111 1111 to 1000 0000 0000) should occur for an
analog value
1
/
2
LSB below analog common. The bipolar
offset error and temperature coefficient specify the initial
deviation and maximum change in the error over tempera-
ture.
Full Scale Calibration Error
The last transition (from 1111 1111 1110 to 1111 1111
1111) should occur for an analog value 1
1
/
2
LSB below the
nominal full scale (9.9963V for 10.000V full scale). The full
scale calibration error is the deviation of the actual level at
the last transition from the ideal level. This error, which is
typically 0.05 to 0.1% of full scale, can be trimmed out as
shown in Figures 2 and 3. The full scale calibration error
over temperature is given with and without the initial error
trimmed out. The temperature coefficients for each grade
indicate the maximum change in the full scale gain from the
initial value using the internal 10V reference.
Pin Descriptions
PIN
SYMBOL
DESCRIPTION
1
V
LOGIC
Logic supply pin (+5V)
2
12/8
Data Mode Select - Selects between
12-bit and 8-bit output modes.
3
CS
Chip Select - Chip Select high disables
the device.
4
A
O
Byte Address/Short Cycle - See Table
1 for operation.
5
R/C
Read/Convert - See Table 1 for
operation.
6
CE
Chip Enable - Chip Enable low disables
the device.
7
V
CC
Positive Supply (+12V/+15V)
8
REF OUT
+10V Reference
9
AC
Analog Common
10
REF IN
Reference Input
11
V
EE
Negative Supply (-12V/-15V).
12
BIP OFF
Bipolar Offset
13
10V Input
10V Input - Used for 0V to 10V and -5V
to +5V input ranges.
14
20V Input
20V Input - Used for 0V to 20V and -10V
to +10V input ranges.
15
DC
Digital Common
16
DB0
Data Bit 0 (LSB)
17
DB1
Data Bit 1
18
DB2
Data Bit 2
19
DB3
Data Bit 3
20
DB4
Data Bit 4
21
DB5
Data Bit 5
22
DB6
Data Bit 6
23
DB7
Data Bit 7
24
DB8
Data Bit 8
25
DB9
Data Bit 9
26
DB10
Data Bit 10
27
DB11
Data Bit 11 (MSB)
28
STS
Status Bit - Status high implies a
conversion is in progress.
HI-574A, HI-674A, HI-774
相关PDF资料 |
PDF描述 |
|---|---|
| HI3-574AKN-5 | JT 16C 16#16 PIN GRND PLUG |
| HI3-674AKN-5 | Circular Connector; No. of Contacts:16; Series:MS27484; Body Material:Aluminum; Connecting Termination:Crimp; Connector Shell Size:20; Circular Contact Gender:Pin; Circular Shell Style:Straight Plug; Insert Arrangement:20-16 RoHS Compliant: No |
| HI1-574ATD-2 | Complete, 12-Bit A/D Converters with Microprocessor Interface |
| HI1-674ATD-2 | Complete, 12-Bit A/D Converters with Microprocessor Interface |
| HI1-574AUD-2 | Complete, 12-Bit A/D Converters with Microprocessor Interface |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5740 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:3V， Dual 10-Bit， 20/ 40/60 MSPS A/D Converter with Internal Voltage Reference (2 pages) FN4821 |
| HI5741 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:14-Bit, 100MSPS, High Speed D/A Converter |
| HI5741_06 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:14-Bit, 100MSPS, High Speed D/A Converter |
| HI5741BIB | 功能描述:IC DAC 14-BIT 100MSPS 28-SOIC RoHS:否 类别:集成电路 (IC) >> 数据采集 - 数模转换器 系列:- 标准包装:2,400 系列:- 设置时间:- 位数:18 数据接口:串行 转换器数目:3 电压电源:模拟和数字 功率耗散（最大）:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:36-TFBGA 供应商设备封装:36-TFBGA 包装:带卷 (TR) 输出数目和类型:* 采样率（每秒）:* |
| HI5741BIBS2503 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。