参数资料
| 型号： | HI5735KCBZ |
| 厂商： | Intersil |
| 文件页数： | 11/11页 |
| 文件大小： | 0K |
| 描述： | CONV D/A 12BIT 80MSPS 28-SOIC |
| 标准包装： | 26 |
| 设置时间： | 20ns |
| 位数： | 12 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字，双 ± |
| 功率耗散（最大）： | 650mW |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 管件 |
| 输出数目和类型： | 2 电流，单极 |
| 采样率（每秒）： | 80M |
9
HI5735
as glitch when changing the DAC output. Units are typically
specified in picoVolt-seconds (pV-s).
Applications
Bipolar Applications
To convert the output of the HI5735 to a bipolar 4V swing, the
following applications circuit is recommended. The reference
can only provide 125
A of drive, so it must be buffered to
create the bipolar offset current needed to generate the -2V
output with all bits “off”. The output current must be converted
to a voltage and then gained up and offset to produce the
proper swing. Care must be taken to compensate for the
voltage swing and error.
Definition of Specifications
Integral Linearity Error, INL, is the measure of the worst
case point that deviates from a best fit straight line of data
values along the transfer curve.
Differential Linearity Error, DNL, is the measure of the
error in step size between adjacent codes along the
converter’s transfer curve. Ideally, the step size is 1 LSB
from one code to the next, and the deviation from 1 LSB is
known as DNL. A DNL specification of greater than -1 LSB
guarantees monotonicity.
Feedthru, is the measure of the undesirable switching noise
coupled to the output.
Output Voltage Full Scale Settling Time, is the time
required from the 50% point on the clock input for a full scale
step to settle within an
±1/
2 LSB error band.
Output Voltage Small Scale Settling Time, is the time
required from the 50% point on the clock input for a 100mV
step to settle within an 1/2 LSB error band. This is used by
applications reconstructing highly correlated signals such as
sine waves with more than 5 points per cycle.
Glitch Area, GE, is the switching transient appearing on the
output during a code transition. It is measured as the area
under the curve and expressed as a picoVoltTime
specification (typically pVs).
Differential Gain,
A
V, is the gain error from an ideal sine
wave with a normalized amplitude.
Differential Phase,
Φ, is the phase error from an ideal sine
wave.
Signal to Noise Ratio, SNR, is the ratio of a fundamental to
the noise floor of the analog output. The first 5 harmonics
are ignored, and an output filter of 1/2 the clock frequency is
used to eliminate alias products.
Total Harmonic Distortion, THD, is the ratio of the DAC
output fundamental to the RMS sum of the harmonics. The
first 5 harmonics are included, and an output filter of 1/2 the
clock frequency is used to eliminate alias products.
Spurious Free Dynamic Range, SFDR, is the amplitude
difference from a fundamental to the largest harmonically or
non-harmonically related spur. A sine wave is loaded into
the D/A and the output filtered at 1/2 the clock frequency to
eliminate noise from clocking alias terms.
Intermodulation Distortion, IMD, is the measure of the
sum and difference products produced when a two tone
input is driven into the D/A. The distortion products created
will arise at sum and difference frequencies of the two tones.
IMD can be calculated using the following equation:
(21) IOUT
100MHz
LOW PASS
FILTER
SCOPE
HI5735
64
50
FIGURE 12. GLITCH TEST CIRCUIT
FIGURE 13. MEASURING GLITCH ENERGY
a (mV)
t (ns)
GLITCH ENERGY = (
a x t)/2
HI5735
REF OUT
IOUT
1/2 CA2904
+
-
+
-
+
-
50
5k
1/2 CA2904
5k
60
240
240
HFA1100
VOUT
0.1
F
FIGURE 14. BIPOLAR OUTPUT CONFIGURATION
(21)
(26)
IMD
20Log (RMS of Sum and Difference Distortion Products)
RMS Amplitude of the Fundamental
()
-------------------------------------------------------------------------------------------------------------------------------------------------------.
=
相关PDF资料 |
PDF描述 |
|---|---|
| HI5741BIBZ | DAC 14BIT 100MHZ 5.2V 28-SOIC |
| HI5746KCB-T | CONV A/D 10BIT 40MSPS 28-SOIC |
| HI5760BIBZ | CONV D/A 10-BIT 125MSPS 28-SOIC |
| HI5762/6IN | CONV A/DDUAL 10BIT 60MSPS 44MQFP |
| HI5766KCB | CONV A/D 10BIT 60MSPS 28-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5735KCP | 制造商:Rochester Electronics LLC 功能描述:28 PDIP COMTEMP D/A 12 BIT 80 MHZ -5.2V - Bulk |
| HI5735KCPS2503 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI573IBIB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI-574 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Complete, 12-Bit A/D Converters with Microprocessor Interface |
| HI5740 | 制造商:未知厂家 制造商全称:未知厂家 功能描述:3V， Dual 10-Bit， 20/ 40/60 MSPS A/D Converter with Internal Voltage Reference (2 pages) FN4821 |
发布紧急采购，3分钟左右您将得到回复。