- 您现在的位置：买卖IC网 > PDF目录10777 > HI5741BIB-T (Intersil)DAC 14BIT 100MHZ 5.2V 28-SOIC PDF资料下载
参数资料
| 型号： | HI5741BIB-T |
| 厂商： | Intersil |
| 文件页数： | 3/13页 |
| 文件大小： | 0K |
| 描述： | DAC 14BIT 100MHZ 5.2V 28-SOIC |
| 标准包装： | 1,000 |
| 设置时间： | 20ns |
| 位数： | 14 |
| 数据接口： | 并联 |
| 转换器数目： | 1 |
| 电压电源： | 模拟和数字，双 ± |
| 功率耗散（最大）： | 650mW |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 28-SOIC W |
| 包装： | 带卷 (TR) |
| 输出数目和类型： | 2 电流，单极；2 电流，双极 |
| 采样率（每秒）： | 100M |
11
FN4071.12
September 20, 2006
to change before another. In order to minimize this, the
Intersil HI5741 employs an internal register, just prior to the
current sources, which is updated on the clock edge. Lastly,
the worst case glitch on traditional D/A converters usually
occurs at the major transition (i.e., code 8191 to 8192).
However, due to the split architecture of the HI5741, the
glitch is moved to the 1023 to 1024 transition (and every
subsequent 1024 code transitions thereafter). This split
R/2R segmented current source architecture, which
decreases the amount of current switching at any one time,
makes the glitch practically constant over the entire output
range. By making the glitch a constant size over the entire
output range this effectively integrates this error out of the
end application.
In measuring the output glitch of the HI5741 the output is
terminated into a 64
load. The glitch is measured at any
one of the current cell carry (code 1023 to 1024 transition or
any multiple thereof) throughout the DACs output range.
The glitch energy is calculated by measuring the area under
the voltage-time curve. Figure 25 shows the area considered
as glitch when changing the DAC output. Units are typically
specified in picoVolt/seconds (pV/s).
Applications
Bipolar Applications
To convert the output of the HI5741 to a bipolar 4V swing,
the following applications circuit is recommended. The
reference can only provide 125
A of drive, so it must be
buffered to create the bipolar offset current needed to
generate the -2V output with all bits ‘off’. The output current
must be converted to a voltage and then gained up and
offset to produce the proper swing. Care must be taken to
compensate for the voltage swing and error.
Interfacing to the HSP45106 NCO-16
The HSP45106 is a 16-bit Numerically Controlled Oscillator
(NCO). The HSP45106 can be used to generate various
modulation schemes for Direct Digital Synthesis (DDS)
applications. Figure 27 shows how to interface an HI5741 to
the HSP45106.
Definition of Specifications
Integral Linearity Error (INL) is the measure of the worst
case point that deviates from a best fit straight line of data
values along the transfer curve.
Differential Linearity Error (DNL) is the measure of the error
in step size between adjacent codes along the converter’s
transfer curve. Ideally, the step size is 1 LSB from one code to
the next, and the deviation from 1 LSB is known as DNL. A
DNL specification of greater than -1 LSB guarantees
monotonicity.
Feedthru is the measure of the undesirable switching noise
coupled to the output.
Output Voltage Full Scale Settling Time is the time
required from the 50% point on the clock input for a full scale
step to settle within an
±1/2 LSB error band.
Output Voltage Small Scale Settling Time is the time
required from the 50% point on the clock input for a 100mV
step to settle within an 1/2 LSB error band. This is used by
applications reconstructing highly correlated signals such as
sine waves with more than 5 points per cycle.
Glitch Area (GE) is the switching transient appearing on the
output during a code transition. It is measured as the area
under the curve and expressed as a volt time specification
(typically pV-s).
Differential Gain (
AV) is the gain error from an ideal sine
wave with a normalized amplitude.
Differential Phase (
Φ) is the phase error from an ideal sine
wave.
(21) IOUT
100MHz
LOW PASS
FILTER
SCOPE
HI5741
64
50
FIGURE 24. GLITCH TEST CIRCUIT
FIGURE 25. MEASURING GLITCH ENERGY
a (mV)
t (ns)
GLITCH ENERGY = (
a x t)/2
HI5741
REF OUT
IOUT
1/2 CA2904
+
-
+
-
+
-
50
5k
1/2 CA2904
5k
60
240
240
HFA1100
VOUT
0.1
F
FIGURE 26. BIPOLAR OUTPUT CONFIGURATION
(21)
(26)
HI5741
相关PDF资料 |
PDF描述 |
|---|---|
| HI5731BIB-T | DAC 12BIT 100MHZ 5.2V 28-SOIC |
| VE-23D-IW-S | CONVERTER MOD DC/DC 85V 100W |
| VE-23D-CU-F3 | CONVERTER MOD DC/DC 85V 200W |
| VE-23B-CU-F4 | CONVERTER MOD DC/DC 95V 200W |
| VE-B6N-MW | CONVERTER MOD DC/DC 18.5V 100W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HI5741BIBZ | 功能描述:数模转换器- DAC 28 INDTEMP D/A 14 BIT 100 MHZ -5 2V RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| HI5741BIBZ-T | 功能描述:数模转换器- DAC HI5741BIB IN TAPE RoHS:否 制造商:Texas Instruments 转换器数量:1 DAC 输出端数量:1 转换速率:2 MSPs 分辨率:16 bit 接口类型:QSPI, SPI, Serial (3-Wire, Microwire) 稳定时间:1 us 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-14 封装:Tube |
| HI5741BIP | 制造商:Rochester Electronics LLC 功能描述:28 PDIP INDTEMP D/A 14 BIT 100 MHZ -5.2V - Bulk 制造商:Harris Corporation 功能描述: 制造商:Intersil Corporation 功能描述: |
| HI5741BIPS2503 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HI5741D DIE | 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。