参数资料
型号: HI5800-EV
厂商: Intersil Corporation
英文描述: 12-Bit, 3MSPS, Sampling A/D Converter
中文描述: 12位,3MSPS,采样A / D转换器
文件页数: 11/15页
文件大小: 234K
代理商: HI5800-EV
11
interfaced to any type of op amp without a requirement for a
high drive capability. Adequate precautions should be taken
while driving the input from high voltage output op amps to
ensure that the analog input pin is not overdriven above the
specified maximum limits. For a +2.5V reference, the analog
input range is
±
2.5V. This input range scales with the value
of the external reference voltage if the internal reference is
not used. For best performance, the analog ground pin next
to the analog input should be utilized for signal return.
Figures 16 and 17 illustrate the use of an input buffer as a
level shifter to convert a unipolar signal to the bipolar input
used by the HI5800. Figure 16 is an example of a non-
inverting buffer that takes a 0 to 2.5V input and shifts it to
±
2.5V. The gain can be calculated from:
Figure 17 is an example of an inverting buffer that level shifts
a 0V to 5V input to
±
2.5V. Its gain can be calculated from:
Note that the correct op amp must be chosen in order to not
degrade the overall dynamic performance of the circuit.
Recommended op amps are called out in the figures.
Voltage Reference, REF
OUT
The HI5800 has a curvature corrected internal band-gap
reference generator with a buffer amplifier capable of driving up
to 15mA. The band-gap and amplifier are trimmed to give
+2.50V. When connected to the reference input pin REF
IN
, the
reference is capable of driving up to 2mA externally. Further
loading may degrade the performance of the output voltage. It
is recommended that the output of the reference be decoupled
with good quality capacitors to reduce the high frequency noise.
Reference Input, REF
IN
The converter requires a voltage reference connected to the
REF
IN
pin. This can be the above internal reference or it can
be an external reference. It is recommended that adequate
high frequency decoupling is provided at the reference input
pin in order to minimize overall converter noise.
A user trying to provide an external reference to a HI5800 is
faced with two problems. First, the drift of the reference over
temperature must be very low. Second, it must be capable of
driving the 200
input impedance seen at the REF
IN
pin of
the HI5800. Figure 18 is a recommended circuit for doing
this that is capable of 2ppm/
o
C drift over temperature.
Supply and Ground Considerations
The HI5800 has separate analog and digital supply and
ground pins to help keep digital noise out of the analog signal
path. For the best performance, the part should be mounted
on a board that provides separate low impedance planes for
the analog and digital supplies and grounds. Only connect the
two grounds together at one place preferably as close as
possible to the part. The supplies should be driven by clean
linear regulated supplies. The board should also have good
high frequency decoupling capacitors mounted as close as
possible to the HI5800.
If the part is powered off a single supply then the analog
supply and ground pins should be isolated by ferrite beads
from the digital supply and ground pins.
Also, it is recommended that the turn-on power supply
sequencing be such that the analog positive supply, AI
CC
,
come up first, followed by the remaining supplies.
Refer to the Application Note “Using Intersil High Speed A/D
Converters” (AN9214) for additional suggestions to consider
when using the HI5800.
Error Adjustments
For most applications the accuracy of the HI5800 is sufficient
without any adjustments. In applications where accuracy is of
utmost importance three external adjustments are possible:
S/Hoffset,D/AoffsetandD/Again.Figure19illustratestheuse
of external potentiometers to reduce the HI5800 errors to zero.
The D/A offset (RO
ADJ
) and S/H offset (ADJ+ and ADJ-)
trims adjust the voltage offset of the transfer curve while the
VOUT
1
)
------------------------
+
VIN
×
R3
--------+
VOFFSET
×
=
R1||R3
R3
----------+
=
-
+
V
IN
HI5800
V
IN
HA2841
0.1
0.1
-15V
+15V
R1
2k
R3
2k
V
OFFSET
R2
1k
V
OUT
FIGURE 16. NON-INVERTING BUFFER
-
+
HI5800
V
IN
HA2841
0.1
0.1
-15V
+15V
R3
2k
V
OFFSET
R2
1k
V
OUT
V
IN
R1
1k
VOUT
R2
R1
(
)
VIN
×
R2 R3
(
)
VOFFSET.
×
=
FIGURE 17. INVERTING BUFFER
HI5800
REF
IN
-
+
-15
-15
10
V
OUT
V
FB
REF101
R
A
R
B
C
10
k
+15
+15
10
μ
+15V
0.1
+
+
10
μ
0.1
LOW TC RESISTOR
FIGURE 18. EXTERNAL REFERENCE
HA5177 HA5002
HI5800
相关PDF资料
PDF描述
HI5800JCD 12-Bit, 3MSPS, Sampling A/D Converter
HI5800KCD 12-Bit, 3MSPS, Sampling A/D Converter
HI5800BID 12-Bit, 3MSPS, Sampling A/D Converter
HI5804 12-Bit, 5 MSPS A/D Converter
HI5804EVAL 12-Bit, 5 MSPS A/D Converter
相关代理商/技术参数
参数描述
HI5800JCD 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:12-Bit, 3MSPS, Sampling A/D Converter
HI5800KCD 制造商:Rochester Electronics LLC 功能描述:40 SBDIP COMTEMP A/D 12BIT 3MSPS 1.0 LSB SMP&HLD V-REF - Bulk 制造商:Harris Corporation 功能描述:
HI5801 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:ADVANCE INFORMATION
HI5801AIJ 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:ADVANCE INFORMATION
HI5801BIJ 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:ADVANCE INFORMATION