- 您现在的位置：买卖IC网 > PDF目录371817 > HIN241 (Integrated Silicon Solution, Inc.) 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors PDF资料下载
参数资料
| 型号： | HIN241 |
| 厂商： | Integrated Silicon Solution, Inc. |
| 元件分类： | RS-232 |
| 英文描述： | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| 中文描述： | 5V的高速RS - 232收发器与0.1uF电容 |
| 文件页数： | 11/15页 |
| 文件大小： | 379K |
| 代理商： | HIN241 |
3-11
Detailed Description
The HIN230 thru HIN241 family of RS-232
transmitters/receivers are powered by a single +5V power
supply (except HIN231 and HIN239), feature low power
consumption, and meet all ElA RS-232C and V.28
specifications. The circuit is divided into three sections: The
charge pump, transmitter, and receiver.
Charge Pump
An equivalent circuit of the charge pump is illustrated in Figure
1. The charge pump contains two sections: the voltage
doubler and the voltage inverter. Each section is driven by a
two phase, internally generated clock to generate +10V and -
10V. The nominal clock frequency is 16kHz. During phase one
of the clock, capacitor C1 is charged to V
CC
. During phase
two, the voltage on C1 is added to V
CC
, producing a signal
across C3 equal to twice V
CC
. During phase one, C2 is also
charged to 2V
CC
, and then during phase two, it is inverted
with respect to ground to produce a signal across C4 equal to
-2V
CC
. The charge pump accepts input voltages up to 5.5V.
The output impedance of the voltage doubler section (V+) is
approximately 200
, and the output impedance of the voltage
inverter section (V-) is approximately 450
. A typical
application uses 1
μ
F capacitors for C1-C4, however, the value
is not critical. Increasing the values of C1 and C2 will lower the
output impedance of the voltage doubler and inverter,
increasing the values of the reservoir capacitors, C3 and C4,
lowers the ripple on the V+ and V- supplies.
During shutdown mode (HIN230, 235, 236, 240 and 241),
SHUTDOWN control line set to logic “1”, the charge pump is
turned off, V+ is pulled down to V
CC
, V- is pulled up to GND,
and the supply current is reduced to less than 10
μ
A. The
transmitter outputs are disabled and the receiver outputs are
placed in the high impedance state.
Transmitters
The transmitters are TTL/CMOS compatible inverters which
translate the inputs to RS-232 outputs. The input logic
threshold is about 26% of V
CC
, or 1.3V for V
CC
= 5V. A logic 1
at the input results in a voltage of between -5V and V- at the
output, and a logic 0 results in a voltage between +5V and (V+ -
0.6V). Each transmitter input has an internal 400k
pullup
resistor so any unused input can be left unconnected and its
output remains in its low state. The output voltage swing meets
the RS-232C specifications of
±
5V minimum with the worst
case conditions of: all transmitters driving 3k
minimum load
impedance, V
CC
= 4.5V, and maximum allowable operating
temperature. The transmitters have an internally limited output
slew rate which is less than 30V/
μ
s. The outputs are short
circuit protected and can be shorted to ground indefinitely. The
powered down output impedance is a minimum of 300
with
±
2V applied to the outputs and V
CC
= 0V.
Receivers
The receiver inputs accept up to
±
30V while presenting the
required 3k
to 7k
input impedance even if the power is off
(V
CC
= 0V). The receivers have a typical input threshold of
1.3V which is within the
±
3V limits, known as the transition
region, of the RS-232 specifications. The receiver output is
0V to V
CC
. The output will be low whenever the input is
greater than 2.4V and high whenever the input is floating or
driven between +0.8V and -30V. The receivers feature 0.5V
hysteresis to improve noise rejection. The receiver Enable
line EN, when set to logic “1”, (HIN235, 236, 239, 240, and
241) disables the receiver outputs, placing them in the high
impedance mode. The receiver outputs are also placed in
the high impedance state when in shutdown mode.
+
-C1
+
-C3
+
-C2
+
-C4
S1
S2
S5
S6
S3
S4
S7
S8
V
CC
GND
RC
OSCILLATOR
V
CC
GND
V+ = 2V
CC
GND
V- = -(V+)
C1
+
C1-
C2
-
C2
+
VOLTAGE INVERTER
VOLTAGE DOUBLER
FIGURE 1. CHARGE PUMP
T
OUT
V- < V
TOUT
< V+
300
400k
T
XIN
GND < T
XIN
< V
CC
V-
V+
V
CC
FIGURE 2. TRANSMITTER
R
OUT
GND < V
ROUT
< V
CC
5k
R
XIN
-30V < R
XIN
< +30V
GND
V
CC
FIGURE 3. RECEIVER
HIN230 thru HIN241
相关PDF资料 |
PDF描述 |
|---|---|
| HIN241CA | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| HIN241CAZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| HIN241CB | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| HIN241CB-T | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
| HIN241CBZ | 5V High-Speed RS-232 Transceivers with 0.1uF Capacitors |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIN241A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:High Speed +5V Powered RS-232 Transmitters/Receivers |
| HIN241ACA | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIN241ACB | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
| HIN241CA | 功能描述:IC 4DRVR/5RCVR RS232 5V 28-SSOP RoHS:否 类别:集成电路 (IC) >> 接口 - 驱动器，接收器，收发器 系列:- 标准包装:1,000 系列:- 类型:收发器 驱动器/接收器数:2/2 规程:RS232 电源电压:3 V ~ 5.5 V 安装类型:表面贴装 封装/外壳:16-SOIC（0.295"，7.50mm 宽） 供应商设备封装:16-SOIC 包装:带卷 (TR) |
| HIN241CAZ | 功能描述:RS-232接口集成电路 RS232 5V 4D/5R 1UF CAPS COM RoHS:否 制造商:Exar 数据速率:52 Mbps 工作电源电压:5 V 电源电流:300 mA 工作温度范围:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体:LQFP-100 封装: |
发布紧急采购，3分钟左右您将得到回复。