- 您现在的位置：买卖IC网 > PDF目录19798 > HIP1011DCAZA (Intersil)IC CTRLR HOTPLUG PCI DUAL 28SSOP PDF资料下载
参数资料
| 型号： | HIP1011DCAZA |
| 厂商： | Intersil |
| 文件页数： | 11/15页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTPLUG PCI DUAL 28SSOP |
| 标准包装： | 240 |
| 类型： | 热交换控制器 |
| 应用： | 通用型 CompactPCI? |
| 内部开关： | 无 |
| 电源电压： | 10.8 V ~ 13.2 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 28-SSOP（0.154"，3.90mm 宽） |
| 供应商设备封装： | 28-SSOP/QSOP |
| 包装： | 管件 |
HIP1011D, HIP1011E
Using the HIP1011DEVAL1 Platform
General and Biasing Information
The HIP1011DEVAL1 platform (Figure 24) comes as a three
part set consisting of 1 motherboard emulator and 2 load
cards. This evaluation platform allows a designer to evaluate
and modify the performance and functionality of the
HIP1011D or HIP1011E in a simple environment.
Test point numbers (TP#) correspond to the HIP1011D/E
device (U5) pin numbers. Thus TP3 and TP12 are
PWRON_2 and PWRON_1 respectively. These 2 pins are
the HIP1011D/E control inputs for each of the 2 integrated
but independent PCI power controllers in the HIP1011D/E.
On the HIP1011DEVAL1 platform are 4 HUF76132SK8,
(11.5m ? , 30V, 11.5A) N-Channel power MOSFETs, (Q1- Q4)
these are used as the external switches for the +5V and
+3.3V supplies to the load card connectors, P1 and P2.
Evaluating Time Delay to Latch-Off
Provided for delay to latch-off evaluation are 2 locations for
SMD capacitors, C7 and C8. Filling these locations places a
capacitor to ground from each of the HIP1011D/E FLTN pins
thus tailoring the FLTN signal going low ramp rate. This
provides a delay to the fault signal latch-off threshold
voltage, FLTN Vth. By increasing this time the HIP1011D
delays immediate latch-off of the bus supply switches, thus
ignoring transient OC and UV conditions. See Table 3
illustrating the time it takes for switch gate turn-off from the
FLTN start of response to an OC or UV condition. The FLTN
response to an OC or UV condition is 110ns. See Figures 20
through 23 for waveforms.
The intent of any protection device is to isolate the supply
quickly so a faulty card does not drag down a supply. A
longer latch-off delay results in less isolation from a faulty
card to supply.
Current sensing is facilitated by the four 5m ? 1W metal strip
resistors (R1-R4), the voltages developed across the sense
resistors are compared to references on board the
C7 AND C8 VALUE
TABLE 3.
OPEN 0.001 μ F
0.01 μ F
0.1 μ F
HIP1011D/E.
FLTN to Gate Response
0.1 μ s
0.44 μ s
2.9 μ s
28 μ s
The HIP1011DEVAL1 platform is powered through the J1 to
J5 connector jacks near the top of the board (see Table 2 for
bias voltage assignments.)
TABLE 2. HIP1011DEVAL1 BIAS ASSIGNMENTS
FLTN
J1
J2
J3
J4
J5
GND
+5V
-12V
+12V
+3.3V
3V5VG
FLTN, Vth
After properly biasing the HIP1011D/E and ensuring there is an
adequate ground return from the HIP1011DEVAL1 platform to
the power supplies, (otherwise anomalous and unpredictable
results will occur) signal the PWRON inputs low then insert the
load cards as shown in Figure 15. Signaling either or both
PWRON pins high (>2.4V) will turn on the appropriate FET
switches and apply voltage to the load cards.
LOAD CARDS
10ms
1ms
100μs
10μs
1μs
100ns
10ns
FIGURE 16. TIMING DIAGRAM
HIP1011D
1ns
OPEN
0.001μF
0.01μF
0.1μF
1μF
10μF
FIGURE 17. TYPICAL OC/UV TO VG RESPONSE vs FLTN CAP
FIGURE 15. CORRECT INSTALLATION OF LOAD CARDS
* The HIP1011DEVAL board is supplied with a HIP1011D
installed and in addition a loose packed HIP1011E.
11
FN4725.5
November 18, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| ECM08DTAI-S189 | CONN EDGECARD 16POS R/A .156 SLD |
| LNK584DG | IC OFFLINE SWITCHER 3W 8-SOIC |
| AYM22DRMT-S288 | CONN EDGECARD 44POS .156 EXTEND |
| GMM36DTMN-S273 | CONN EDGECARD 72POS R/A .156 SLD |
| ELJ-NC33NJF | INDUCTOR 33NH 5% FIXED SMD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP1011DCAZA-T | 功能描述:热插拔功率分布 W/ANNEAL DL PCI HOT PLUG PWR CNTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| HIP1011DEVAL1 | 功能描述:电源管理IC开发工具 DL SLOT PCI HOT PLUG EVALUATION BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP1011E | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Dual Slot PCI Hot Plug Controller |
| HIP1011ECA | 功能描述:IC CTRLR HOTPLUG DUAL 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
| HIP1011ECA-T | 功能描述:IC CTRLR HOTPLUG DUAL 28-SSOP RoHS:否 类别:集成电路 (IC) >> PMIC - 热交换 系列:- 产品培训模块:Obsolescence Mitigation Program 标准包装:100 系列:- 类型:热插拔开关 应用:通用 内部开关:是 电流限制:可调 电源电压:9 V ~ 13.2 V 工作温度:-40°C ~ 150°C 安装类型:表面贴装 封装/外壳:10-WFDFN 裸露焊盘 供应商设备封装:10-TDFN-EP（3x3） 包装:管件 |
发布紧急采购，3分钟左右您将得到回复。