- 您现在的位置：买卖IC网 > PDF目录19711 > HIP1013CB-T (Intersil)IC CTRLR HOTPLUG DUAL 14-SOIC PDF资料下载
参数资料
| 型号： | HIP1013CB-T |
| 厂商： | Intersil |
| 文件页数： | 3/8页 |
| 文件大小： | 0K |
| 描述： | IC CTRLR HOTPLUG DUAL 14-SOIC |
| 标准包装： | 2,500 |
| 类型： | 热交换控制器 |
| 应用： | 通用 |
| 内部开关： | 无 |
| 电源电压： | 10.5 V ~ 16 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | 14-SOICN |
| 包装： | 带卷 (TR) |
HIP1013
Pin Description
PIN NO.
1
SYMBOL
12VS
FUNCTION
12V Source
DESCRIPTION
Connect to source of associated external N-Channel MOSFET switch to sense output
voltage.
2
3
12VG
V DD
12V Gate
Chip Supply
Connect to the gate of associated N-Channel MOSFET switch. A capacitor from this
node to ground sets the turn-on ramp. At turn-on this capacitor will be charged to ≈ 17.4V
by a 10 μ A current source when in 5V/12V mode of operation, otherwise capacitor will be
charged to ≈ 11.4V.
Connect to 12V supply. This can be either connected directly to the +12V rail supplying
the load voltage or to a dedicated V DD +12V supply.
4
MODE/
PWRON1
Power ON/ Reset invokes
3.3V operation when
shorted to V DD , Pin 3.
PWRON1 and PWRON2 are used to turn-on and reset the chip. Both outputs turn-on
when either pin is driven low. After an over current limit fault, the chip is reset by the rising
edge of a reset signal applied to either PWRON pin. Each input has 100 μ A pull up
capability which is compatible with 3V and 5V open drain and standard logic. PWRON1
5
6
7
PWRON2
5VG
5VS
Power ON/Reset
5V Gate
5V Source
is also used to invoke 3.3V control operation in preference to +12V control. By tying pin
4 to pin 3 the charge pump is disabled and the UV threshold also shifts to ≈ 2.8V.
Connect to the gate of the external 5V N-Channel MOSFET. A capacitor from this node
to ground sets the turn-on ramp. At turn-on this capacitor will be charged to ≈ 11.4V by a
10 μ A current source.
Connect to the source side of 5V external N-Channel MOSFET switch to sense output
voltage.
8
5VISEN
5V Current Sense
Connect to the load side of the 5V sense resistor to measure the voltage drop across this
resistor between 5VS and 5VISEN pins.
9
PGOOD
Power Good Indicator
PGOOD is driven by an open drain N-Channel MOSFET. It is pulled low when either
output voltage is not within specification or and OC condition exists.
10
No Connection.
11
12
13
C PUMP
GND
R ILIM
Charge Pump Capacitor
Chip Ground
Current Limit Set Resistor
Connect a 0.1 μ F capacitor between this pin and V DD (Pin 3).
A resistor connected between this pin and ground determines the current level at which
current limit is activated. This current is determined by the ratio of the R ILIM resistor to
the sense resistor (R SENSE ). The current at current limit onset is equal to
10 μ A x (R ILIM / R SENSE ).
14
12VISEN
12V Current Sense
Connect to the load side of sense resistor to measure the voltage drop across this
resistor.
3
相关PDF资料 |
PDF描述 |
|---|---|
| 182-037-213R531 | CONN DB37 FEMAL .318" R/A NICKEL |
| MIC39501-1.8BU | IC REG LDO 1.8V 5A TO-263-5 |
| 172-E25-101R011 | CONN DB25 MALE SOLDER CUP CHROME |
| TAP106M010FCS | CAP TANT 10UF 10V 20% RADIAL |
| GEC08DREH | CONN EDGECARD 16POS .100 EYELET |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP1013CBZA | 功能描述:热插拔功率分布 W/ANNEAL DUAL PWR DISTRIBUTION CONTRLR RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| HIP1013CBZA-T | 功能描述:热插拔功率分布 W/ANNEAL PWR DIST TRLR W/OUT CURRE RoHS:否 制造商:Texas Instruments 产品:Controllers & Switches 电流限制: 电源电压-最大:7 V 电源电压-最小:- 0.3 V 工作温度范围: 功率耗散: 安装风格:SMD/SMT 封装 / 箱体:MSOP-8 封装:Tube |
| HIP1013EVAL1 | 功能描述:电源管理IC开发工具 GENERIC DL PWR DIST CNTRLR EVAL BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP1013EVAL2 | 功能描述:电源管理IC开发工具 GENERIC HIP1013 RAID EVALUATION BRD RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP1015 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Power Distribution Controllers |
发布紧急采购，3分钟左右您将得到回复。