- 您现在的位置：买卖IC网 > PDF目录20538 > HIP4020IB (Intersil)IC DRIVER FULL-BRIDGE 20-SOIC PDF资料下载
参数资料
| 型号： | HIP4020IB |
| 厂商： | Intersil |
| 文件页数： | 3/9页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER FULL-BRIDGE 20-SOIC |
| 标准包装： | 760 |
| 配置： | 半桥 |
| 输入类型： | 反相和非反相 |
| 延迟时间： | 2.5µs |
| 电流 - 峰： | 625mA |
| 配置数： | 1 |
| 输出数： | 4 |
| 电源电压： | 3 V ~ 12 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 管件 |
HIP4020
Absolute Maximum Ratings
Supply Voltage; V DD to V SS or V SSA or V SSB . . . . . . . . . . . . .+15V
Neg. Output Supply Voltage, (V SSA , V SSB ) . . . . . . . . . . . . (Note 1)
DC Logic Input Voltage (Each Input) . . . (V SS -0.5V) to (V DD +0.5V)
DC Logic Input Current (Each Input) . . . . . . . . . . . . . . . . . . . . . ± 15mA
ILF Fault Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 15mA
Output Load Current, (Self Limiting, See Elec. Spec.) . . . . ± I O(LIMIT)
Thermal Information
Thermal Resistance (Typical, Note 2) θ JA (°C/W)
Plastic SOIC Package . . . . . . . . . . . . . . . . . . . . . . . 105
Maximum Storage Temperature Range . . . . . . . . . . . -65°C to 150°C
Maximum Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
Maximum Lead Temperature (Soldering 10s) . . . . . . . . . . . . . 300°C
(Lead Tips Only)
Operating Conditions T A = 25°C
Typical Operating Supply Voltage Range, V DD . . . . . . . +3 to +12V
Low Voltage Logic Retention, Min. V DD . . . . . . . . . . . . . . . . . . . .+2V
Idle Supply Current; No Load, V DD = +5V. . . . . . . . . . . . . . . .0.8mA
Typical P+N Channel r DS(ON) , V DD = +5V, 0.5A Load . . . . . . . . 2 ?
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
NOTES:
1. V SS is the required common ground reference for the logic input switching. The load currents may be switched positive and negative in reference
to the V SS common ground by using a split supply for V DD (positive) to V SSA and V SSB (negative). For an uneven split in the supply voltage,
the Maximum Negative Output Supply Voltage for V SSA and V SSB is limited by the Maximum V DD to V SSA or V SSB ratings. Since the V DD pins
are internally tied together, the voltage on each V DD pins must be equal and common.
2. θ JA is measured with the component mounted on an evaluation PC board in free air.
3. Refer to the Truth Table and the V EN to V OUT Switching Waveforms. Current, I O refers to I OUTA or I OUTB as the Output Load current. Note that
ENA controls OUTA and ENB controls OUTB. Each Half H-Switch has independent control from the respective A1, A2, ENA or B1, B2, ENB
inputs. Refer to the Terminal Information Table for external pin connections to establish mode control switching. Figure 1 shows a typical
application circuit used to control a DC Motor.
Electrical Specifications
T A = 25°C, V DD = +5V, V SSA = V SSB = V SS = 0V, Unless Otherwise Specified
PARAMETER
Input Leakage Current
Low Level Input Voltage
High Level Input Voltage
ILF Output Low, Sink Current
ILF Output High, Source Current
Input Capacitance
P-Channel rDS(ON), Low Supply Voltage
N-Channel rDS(ON), Low Supply Voltage
P-Channel rDS(ON), High Supply Voltage
N-Channel rDS(ON), High Supply Voltage
OUTA, OUTB Source Current Limiting
OUTA, OUTB Sink Current Limiting
Idle Supply Current; No Load
OUTA, OUTB Voltage High
OUTA, OUTB Voltage Low
OUTA, OUTB Voltage High
OUTA, OUTB Voltage Low
OUTA, OUTB Source Current Limiting
OUTA, OUTB Sink Current Limiting
OUTA, OUTB Source Current Limiting
OUTA, OUTB Sink Current Limiting
SYMBOL
I LEAK
V IL
V IH
I OH
I OL
C IN
rDS(ON)
rDS(ON)
rDS(ON)
rDS(ON)
I O(LIMIT)
-I O(LIMIT)
I DD
V OH
V OL
V OH
V OL
I O(LIMIT)
-I O(LIMIT)
I O(LIMIT)
-I O(LIMIT)
TEST CONDITIONS
V DD = +15V
V OUT = 0.4V, V DD = +12V
V OUT = 11.6V, V DD = +12V
V DD = +3V, I SOURCE = 250mA
V DD = +3V, I SINK = 250mA
V DD = +12V, I SOURCE = 400mA
V DD = +12V, I SINK = 400mA
V DD = +6V, V SS = 0V, V SSA = V SS B = -6V
V DD = +6V, V SS = 0V, V SSA = V SS B = -6V
I SOURCE = 450mA
I SINK = 450mA
V DD = +3V, I SOURCE = 250mA
V DD = +3V, I SINK = 250mA
V DD = +12V
V DD = +12V
V DD = +3V
V DD = +3V
MIN
-
V SS
2
15
-
-
-
-
-
-
480
480
-
4.2
-
2.415
-
480
480
480
480
TYP
-
-
-
-
-
2
1.6
1
0.6
0.5
625
800
0.8
4.5
0.4
2.6
0.25
625
800
625
800
MAX
25
0.8
V DD
-
-15
-
2.1
1.5
1.2
1.1
1500
1500
1.5
-
0.6
-
0.375
1500
1500
1500
1500
UNITS
nA
V
V
mA
mA
pF
?
?
?
?
mA
mA
mA
V
V
V
V
mA
mA
mA
mA
3
FN3976.3
December 20, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| REC3-2409SRWZ/H6/C | CONV DC/DC 3W 9-36VIN 09VOUT |
| VE-23W-CX-S | CONVERTER MOD DC/DC 5.5V 75W |
| T95Z476K010LZAL | CAP TANT 47UF 10V 10% 2910 |
| EGM12DRMH | CONN EDGECARD 24POS .156 WW |
| VE-23T-CX-S | CONVERTER MOD DC/DC 6.5V 75W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP4020IBZ | 功能描述:马达/运动/点火控制器和驱动器 W/ANNEAL FL BRDG MOTOR DRVR/CNTRLR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| HIP4020IBZT | 功能描述:马达/运动/点火控制器和驱动器 W/ANNEAL FL BRDG MOTOR DRVR/CNTRLR RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
| HIP4080 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:80V/2.5A Peak, High Frequency Full Bridge FET Driver |
| HIP4080_03 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:80V/2.5A Peak, High Frequency Full Bridge FET Driver |
| HIP4080A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:80V/2.5A Peak, High Frequency Full Bridge FET Driver |
发布紧急采购，3分钟左右您将得到回复。