- 您现在的位置：买卖IC网 > PDF目录17261 > HIP4080AIBZT (Intersil)IC DRIVER FET FULL 80V 20-SOIC PDF资料下载
参数资料
| 型号： | HIP4080AIBZT |
| 厂商： | Intersil |
| 文件页数： | 7/17页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER FET FULL 80V 20-SOIC |
| 标准包装： | 1 |
| 配置： | 半桥 |
| 输入类型： | 非反相 |
| 延迟时间： | 70ns |
| 电流 - 峰： | 2.6A |
| 配置数： | 1 |
| 输出数： | 4 |
| 高端电压 - 最大（自引导启动）： | 95V |
| 电源电压： | 9.5 V ~ 15 V |
| 工作温度： | -40°C ~ 85°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 20-SOIC W |
| 包装： | 标准包装 |
| 产品目录页面： | 1239 (CN2011-ZH PDF) |
| 其它名称： | HIP4080AIBZTDKR |
HIP4080A
Pin Descriptions
PIN
NUMBER
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
SYMBOL
BHB
HEN
DIS
V SS
OUT
IN+
IN-
HDEL
LDEL
AHB
AHO
AHS
ALO
ALS
V CC
V DD
BLS
BLO
BHS
BHO
DESCRIPTION
B High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap
diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30 μ A out of this pin to
maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
High-side Enable input. Logic level input that when low overrides IN+/IN- (Pins 6 and 7) to put AHO and BHO drivers
(Pins 11 and 20) in low output state. When HEN is high AHO and BHO are controlled by IN+/IN- inputs. The pin can
be driven by signal levels of 0V to 15V (no greater than V DD ).
DISable input. Logic level input that when taken high sets all four outputs low. DIS high overrides all other inputs.
When DIS is taken low the outputs are controlled by the other inputs. The pin can be driven by signal levels of 0V to
15V (no greater than V DD ).
Chip negative supply, generally will be ground.
OUTput of the input control comparator. This output can be used for feedback and hysteresis.
Noninverting input of control comparator. If IN+ is greater than IN- (Pin 7) then ALO and BHO are low level outputs
and BLO and AHO are high level outputs. If IN+ is less than IN- then ALO and BHO are high level outputs and BLO
and AHO are low level outputs. DIS (Pin 3) high level will override IN+/IN- control for all outputs. HEN (Pin 2) low level
will override IN+/IN- control of AHO and BHO. When switching in four quadrant mode, dead time in a half bridge leg
is controlled by HDEL and LDEL (Pins 8 and 9).
Inverting input of control comparator. See IN+ (Pin 6) description.
High-side turn-on DELay. Connect resistor from this pin to V SS to set timing current that defines the turn-on delay of
both high-side drivers. The low-side drivers turn-off with no adjustable delay, so the HDEL resistor guarantees no
shoot-through by delaying the turn-on of the high-side drivers. HDEL reference voltage is approximately 5.1V.
Low-side turn-on DELay. Connect resistor from this pin to V SS to set timing current that defines the turn-on delay of
both low-side drivers. The high-side drivers turn-off with no adjustable delay, so the LDEL resistor guarantees no
shoot-through by delaying the turn-on of the low-side drivers. LDEL reference voltage is approximately 5.1V.
A High-side Bootstrap supply. External bootstrap diode and capacitor are required. Connect cathode of bootstrap
diode and positive side of bootstrap capacitor to this pin. Internal charge pump supplies 30 μ A out of this pin to
maintain bootstrap supply. Internal circuitry clamps the bootstrap supply to approximately 12.8V.
A High-side Output. Connect to gate of A High-side power MOSFET.
A High-side Source connection. Connect to source of A High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
A Low-side Output. Connect to gate of A Low-side power MOSFET.
A Low-side Source connection. Connect to source of A Low-side power MOSFET.
Positive supply to gate drivers. Must be same potential as V DD (Pin 16). Connect to anodes of two bootstrap diodes.
Positive supply to lower gate drivers. Must be same potential as V CC (Pin 15). De-couple this pin to V SS (Pin 4).
B Low-side Source connection. Connect to source of B Low-side power MOSFET.
B Low-side Output. Connect to gate of B Low-side power MOSFET.
B High-side Source connection. Connect to source of B High-side power MOSFET. Connect negative side of
bootstrap capacitor to this pin.
B High-side Output. Connect to gate of B High-side power MOSFET.
7
相关PDF资料 |
PDF描述 |
|---|---|
| CB2016T100K | INDUCTOR POWER 10UH 520MA 0806 |
| R1S12-1209 | CONV DC/DC 1W 12VIN 09VOUT |
| 195D154X9050C2T | CAP TANT 0.15UF 50V 10% 0905 |
| GEM15DRSN-S288 | CONN EDGECARD 30POS .156 EXTEND |
| 100R30-203B | CABLE FLAT FLEX 30POS 1MM 8" |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP4080AIP | 功能描述:功率驱动器IC 60-80 VDC HI FREQ H- BRDG DRIVER RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| HIP4080AIPR3165 | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP4080AIPZ | 功能描述:功率驱动器IC 60-80VDC HI FREQ H-B RDG DRVR W/ RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| HIP4080IB | 制造商:Harris Corporation 功能描述: |
| HIP4080IB WAF | 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。