- 您现在的位置：买卖IC网 > PDF目录17255 > HIP4086AB (Intersil)IC DRIVER 3-PHASE FET 24-SOIC PDF资料下载
参数资料
| 型号： | HIP4086AB |
| 厂商： | Intersil |
| 文件页数： | 12/16页 |
| 文件大小： | 0K |
| 描述： | IC DRIVER 3-PHASE FET 24-SOIC |
| 产品培训模块： | Solutions for Industrial Control Applications |
| 标准包装： | 30 |
| 配置： | 3 相桥 |
| 输入类型： | 反相和非反相 |
| 延迟时间： | 65ns |
| 电流 - 峰： | 500mA |
| 配置数： | 1 |
| 输出数： | 3 |
| 高端电压 - 最大（自引导启动）： | 95V |
| 电源电压： | 7 V ~ 15 V |
| 工作温度： | -40°C ~ 125°C |
| 安装类型： | 表面贴装 |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | 24-SOIC |
| 包装： | 管件 |
| 产品目录页面： | 1239 (CN2011-ZH PDF) |
HIP4086, HIP4086A
Typical Application Circuit
VDD
VDD
RDEL
CHB
BHB
AHB
AHO
BHO
Battery
Speed
Controller
AHI
ALI
BHI
BLI
CHO
CHS
BHS
AHS
24V...48V
Brake
CHI
CLI
VSS
ALO
BLO
CLO
FIGURE 22. TYPICAL APPLICATION CIRCUIT
Figure 22 is an example of how the HIP4086 and HIP4086A
3-phase drivers can be applied to drive a 3-phase motor.
Depending on the application, the switching speed of the bridge
FETs can be reduced by adding series connected resistors
between the xHO outputs and the FET gates. Gate-Source
resistors are recommended on the low-side FETs to prevent
unexpected turn-on of the bridge should the bridge voltage be
applied before V DD . Gate-source resistors on the high-side FETs
are not usually required if low-side gate-source resistors are
used. If relatively small gate-source resistors are used on the
high-side FETs, be aware that they will load the charge pump of
the HIP4086 negating the ability of the charge pump to keep the
high-side driver biased during very long periods.
An important operating condition that is frequently overlooked by
designers is the negative transient on the xHS pins that occurs
when the high-side bridge FET turns off. The Absolute Maximum
transient allowed on the xHS pin is -6V but it is wise to minimize
the amplitude to lower levels. This transient is the result of the
parasitic inductance of the low-side drain-source conductor on
the PCB. Even the parasitic inductance of the low-side FET
contributes to this transient.
When the high-side bridge FET turns off, because of the inductive
characteristics of a motor load, the current that was flowing in
the high-side FET (blue) must rapidly commutate to flow through
the low-side FET (red). The amplitude of the negative transient
impressed on the xHS node is (di/dt x L) where L is the total
parasitic inductance of the low-side FET drain-source path and
di/ddt is the rate at which the high-side FET is turned off. With
the increasing power levels of new generation motor drives,
clamping this transient becomes more and more significant for
the proper operation of the HIP4086/A.
There are several ways of reducing the amplitude of this
transient. If the bridge FETs are turned off more slowly to reduce
di/dt, the amplitude will be reduced but at the expense of more
switching losses in the FETs. Careful PCB design will also reduce
the value of the parasitic inductance. However, these two
solutions by themselves may not be sufficient. Figure 23
illustrates a simple method for clamping the negative transient.
Two series connected, fast PN junction, 1A diodes are connected
between xHS and VSS as shown. It is important that the
components be placed as close as possible to the xHS and VSS
pins to minimize the parasitic inductance of this current path.
Two series connected diodes are required because they are in
parallel with the body diode of the low-side FET. If only one diode
xHO
xHS
xLO
VSS
-
+
-
+
IN D U C T IV E
LO AD
is used for the clamp, it will conduct some of the negative load
current that is flowing in the low-side FET. In severe cases, a
small value resistor in series with the xHS pin as shown, will
further reduce the amplitude of the negative transient.
Please note that a similar transient with a positive polarity occurs
when the low-side FET turns off. This is less frequently a problem
because xHS node is floating up toward the bridge bias voltage.
The Absolute Max voltage rating for the xHS node does need to
FIGURE 23. BRIDGE WITH PARASITIC INDUCTANCES
12
be observed when the positive transient occurs.
FN4220.9
February 1, 2013
相关PDF资料 |
PDF描述 |
|---|---|
| HIP4080AIP | IC DRIVER FULL-BRIDGE 20-DIP |
| T95S475K6R3EZSL | CAP TANT 4.7UF 6.3V 10% 1507 |
| T95S335M016EZSL | CAP TANT 3.3UF 16V 20% 1507 |
| T95S335M010EZSL | CAP TANT 3.3UF 10V 20% 1507 |
| 21020-0429 | CABLE FLAT FLEX 3" .50MM 40 POS |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP4086AB/AP DIE | 制造商:Harris Corporation 功能描述: |
| HIP4086ABT | 功能描述:功率驱动器IC VER OF HIP4086AB RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| HIP4086ABZ | 功能描述:功率驱动器IC 80V 1.25A 3 PHS FL W V DRVR RoHS:否 制造商:Micrel 产品:MOSFET Gate Drivers 类型:Low Cost High or Low Side MOSFET Driver 上升时间: 下降时间: 电源电压-最大:30 V 电源电压-最小:2.75 V 电源电流: 最大功率耗散: 最大工作温度:+ 85 C 安装风格:SMD/SMT 封装 / 箱体:SOIC-8 封装:Tube |
| HIP4086ABZATS2490 | 制造商:Intersil Corporation 功能描述:IBM HIP4086ABZT W/CONTAINER LABELING - Bulk |
| HIP4086ABZT | 功能描述:马达/运动/点火控制器和驱动器 VER OF HIP4086AB RoHS:否 制造商:STMicroelectronics 产品:Stepper Motor Controllers / Drivers 类型:2 Phase Stepper Motor Driver 工作电源电压:8 V to 45 V 电源电流:0.5 mA 工作温度:- 25 C to + 125 C 安装风格:SMD/SMT 封装 / 箱体:HTSSOP-28 封装:Tube |
发布紧急采购，3分钟左右您将得到回复。