- 您现在的位置：买卖IC网 > PDF目录385382 > HIP6003CB (HARRIS SEMICONDUCTOR) Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor PDF资料下载
参数资料
| 型号： | HIP6003CB |
| 厂商： | HARRIS SEMICONDUCTOR |
| 元件分类： | 稳压器 |
| 英文描述： | Buck Pulse-Width Modulator (PWM) Controller and Output Voltage Monitor |
| 中文描述： | SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO16 |
| 文件页数： | 6/12页 |
| 文件大小： | 208K |
| 代理商： | HIP6003CB |
6
converter dissipates very little power with this method. The
measured input power for the conditions of Figure 4 is 2.5W.
The over-current function will trip at a peak inductor current
(I
PEAK)
determined by:
DS ON
)
where I
OCSET
is the internal OCSET current source (200
μ
A
typical). The OC trip point varies mainly due to the MOSFETs
r
DS(ON)
variations. To avoid over-current tripping in the
normal operating load range, find the R
OCSET
resistor from
the equation above with:
1. The maximum r
DS(ON)
at the highest junction temperature.
2. The minimum I
OCSET
from the specification table.
3. Determine I
PEAK
for I
PEAK
> I
OUT(MAX)
+ (
I)/2, where
I
is the output inductor ripple current.
For an equation for the ripple current see the section under
component guidelines titled ‘Output Inductor Selection’.
A small ceramic capacitor should be placed in parallel with
R
OCSET
to smooth the voltage across R
OCSET
in the
presence of switching noise on the input voltage.
Output Voltage Program
The output voltage of a HIP6003 converter is programmed to
discrete levels between 2.0VDC and 3.5VDC. The voltage
identification (VID) pins program an internal voltage
reference (DACOUT) with a 4-bit digital-to-analog converter
(DAC). The level of DACOUT also sets the PGOOD and
OVP thresholds. Table 1 specifies the DACOUT voltage for
the 16 combinations of open or short connections on the VID
pins. The output voltage should not be adjusted while the
converter is delivering power. Remove input power before
changing the output voltage. Adjusting the output voltage
during operation could toggle the PGOOD signal and
exercise the overvoltage protection.
The DAC function is a precision non-inverting summation
amplifier shown in Figure 5. The resistor values shown are
only approximations of the actual precision values used.
Grounding any combination of the VID pins increases the
DACOUT voltage. The ‘open’ circuit voltage on the VID pins
is the band gap reference voltage, 1.26V.
O
S
0A
0V
TIME (20ms/DIV)
5A
10A
15A
2V
4V
FIGURE 4. OVER-CURRENT OPERATION
I
PEAK
=
I
---------------------------------------------------
R
TABLE 1. OUTPUT VOLTAGE PROGRAM
PIN NAME
NOMINAL
DACOUT
VOLTAGE
VID3
VID2
VID1
VID0
1
1
1
1
2.0
1
1
1
0
2.1
1
1
0
1
2.2
1
1
0
0
2.3
1
0
1
1
2.4
1
0
1
0
2.5
1
0
0
1
2.6
1
0
0
0
2.7
0
1
1
1
2.8
0
1
1
0
2.9
0
1
0
1
3.0
0
1
0
0
3.1
0
0
1
1
3.2
0
0
1
0
3.3
0
0
0
1
3.4
0
0
0
0
3.5
NOTE: 0 = Connected to GND or V
SS
, 1 = OPEN
+
-
BAND GAP
REFERENCE
1.26V
VID0
VID1
VID2
VID3
FB
COMP
DACOUT
ERROR
AMPLIFIER
21.5k
1.7k
10.7k
5.4k
2.7k
2.9k
DAC
+
-
FIGURE 5. DAC FUNCTION SCHEMATIC
HIP6003
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6004BCB | Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6004BCV | Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6004ECBZ | Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6004ECVZ | Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6004E | Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6003CB-T | 制造商:未知厂家 制造商全称:未知厂家 功能描述:Voltage-Mode SMPS Controller |
| HIP6003EVAL1 | 制造商:Rochester Electronics LLC 功能描述:P PRO VRM EVALUATION BOARD - STD BUCK - Bulk 制造商:Harris Corporation 功能描述: |
| HIP6004 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6004 WAF | 制造商:Intersil Corporation 功能描述: |
| HIP6004A | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
发布紧急采购，3分钟左右您将得到回复。