参数资料
型号: HIP6006CB
厂商: Intersil
文件页数: 4/12页
文件大小: 0K
描述: IC CTRLR PWM VOLTAGE MODE 14SOIC
标准包装: 50
应用: 控制器,Intel Pentium? Pro、PowerP、Alpha
输入电压: 5V,12V
输出数: 1
输出电压: 1.3 V ~ 12 V
工作温度: 0°C ~ 70°C
安装类型: *
封装/外壳: 14-SOIC(0.154",3.90mm 宽)
供应商设备封装: *
包装: 管件
HIP6006
Typical Performance Curves
80
70
1000
100
10
R T PULLUP
TO +12V
R T PULLDOWN
TO V SS
60
50
40
30
20
10
C GATE = 3300pF
C GATE = 1000pF
C GATE = 10pF
10
100
SWITCHING FREQUENCY (kHz)
1000
0
100
200
300 400 500 600 700 800
SWITCHING FREQUENCY (kHz)
900
1000
FIGURE 1. R T RESISTANCE vs FREQUENCY
Functional Pin Description
FIGURE 2. BIAS SUPPLY CURRENT vs FREQUENCY
SS (Pin 3)
Connect a capacitor from this pin to ground. This capacitor,
RT
OCSET
SS
COMP
FB
1
2
3
4
5
14 VCC
13 PVCC
12 LGATE
11 PGND
10 BOOT
along with an internal 10 μ A current source, sets the soft-start
interval of the converter.
COMP (Pin 4) and FB (Pin 5)
COMP and FB are the available external pins of the error
amplifier. The FB pin is the inverting input of the error
EN
GND
6
7
9
8
UGATE
PHASE
amplifier and the COMP pin is the error amplifier output.
These pins are used to compensate the voltage-control
feedback loop of the converter.
RT (Pin 1)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R T ) from this pin to GND, the nominal
200kHz switching frequency is increased according to the
following equation:
EN (Pin 6)
This pin is the open-collector enable pin. Pull this pin below
1V to disable the converter. In shutdown, the soft start pin is
discharged and the UGATE and LGATE pins are held low.
5 ? 10
R T ( k ? )
6
Fs ≈ 200kHz + ---------------------
(R T to GND)
GND (Pin 7)
Signal ground for the IC. All voltage levels are measured
with respect to this pin.
4 ? 10
(R T to 12V)
R T ( k ? )
I PEAK = --------------------------------------------
Conversely, connecting a pull-up resistor (R T ) from this pin
to V CC reduces the switching frequency according to the
following equation.:
7
Fs ≈ 200kHz – ---------------------
OCSET (Pin 2)
Connect a resistor (R OCSET ) from this pin to the drain of the
upper MOSFET. R OCSET , an internal 200 μ A current source
(I OCS ), and the upper MOSFET on-resistance (r DS(ON) ) set
the converter over-current (OC) trip point according to the
following equation:
I OCS ? R OCSET
r DS ( ON )
An over-current trip cycles the soft-start function.
PHASE (Pin 8)
Connect the PHASE pin to the upper MOSFET source. This
pin is used to monitor the voltage drop across the MOSFET
for over-current protection. This pin also provides the return
path for the upper gate drive.
UGATE (Pin 9)
Connect UGATE to the upper MOSFET gate. This pin
provides the gate drive for the upper MOSFET.
BOOT (Pin 10)
This pin provides bias voltage to the upper MOSFET driver.
A bootstrap circuit may be used to create a BOOT voltage
suitable to drive a standard N-Channel MOSFET.
PGND (Pin 11)
This is the power ground connection. Tie the lower MOSFET
source to this pin.
4
相关PDF资料
PDF描述
UWZ0J152MCL1GS CAP ALUM 1500UF 6.3V 20% SMD
HIP6004ECV IC CTRLR PWM VOLTAGE MON 20TSSOP
HIP6004BCB IC CTRLR PWM VOLTAGE MON 20-SOIC
UVK2V3R3MPD CAP ALUM 3.3UF 350V 20% RADIAL
AHA476M50X16T-F CAP ALUM 47UF 50V 20% SMD
相关代理商/技术参数
参数描述
HIP6006CB-T 功能描述:IC CNTRLR PWM BUCK SYNC 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 标准包装:2,000 系列:- 应用:控制器,DSP 输入电压:4.5 V ~ 25 V 输出数:2 输出电压:最低可调至 1.2V 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:30-TFSOP(0.173",4.40mm 宽) 供应商设备封装:30-TSSOP 包装:带卷 (TR)
HIP6006CB-TS2604 制造商:Rochester Electronics LLC 功能描述:- Bulk
HIP6006CBZ 功能描述:电压模式 PWM 控制器 PWMCNTRLR SYNCBUCK-14" RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
HIP6006CBZ-T 功能描述:电压模式 PWM 控制器 PWMCNTRLR SYNCBUCK-14 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel
HIP6006CBZ-TS2462 制造商:Rochester Electronics LLC 功能描述: 制造商:Intersil Corporation 功能描述: