参数资料
| 型号： | HIP6013CB |
| 厂商： | Intersil |
| 文件页数： | 5/11页 |
| 文件大小： | 0K |
| 描述： | IC CONTROLLER PWM BUCK 14-SOIC |
| 标准包装： | 50 |
| 应用： | 控制器，Intel Pentium? Pro、PowerP、Alpha |
| 输入电压： | 5V，12V |
| 输出数： | 1 |
| 输出电压： | 1.3 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 14-SOIC（0.154"，3.90mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
HIP6013
Functional Description
Initialization
The HIP6013 automatically initializes upon receipt of power.
Special sequencing of the input supplies is not necessary.
The Power-On Reset (POR) function continually monitors
the input supply voltages and the enable (EN) pin. The POR
monitors the bias voltage at the VCC pin and the input
SOFT-START
(1V/DIV)
voltage (V IN ) on the OCSET pin. The level on OCSET is
equal to V IN less a fixed voltage drop (see over-current
protection). With the EN pin held to VCC, the POR function
initiates soft start operation after both input supply voltages
exceed their POR thresholds. For operation with a single
0V
0V
OUTPUT
VOLTAGE
(1V/DIV)
+12V power source, V IN and V CC are equivalent and the
t1
t2
t3
+12V power source must exceed the rising V CC threshold
before POR initiates operation.
The Power-On Reset (POR) function inhibits operation with
the chip disabled (EN pin low). With both input supplies
above their POR thresholds, transitioning the EN pin high
initiates a soft start interval.
Soft Start
The POR function initiates the soft start sequence. An
internal 10 μ A current source charges an external capacitor
(C SS ) on the SS pin to 4V. Soft start clamps the error
amplifier output (COMP pin) and reference input (+ terminal
of error amp) to the SS pin voltage. Figure 3 shows the soft
start interval with C SS = 0.1 μ F. Initially the clamp on the error
amplifier (COMP pin) controls the converter’s output voltage.
At t1 in Figure 3, the SS voltage reaches the valley of the
oscillator’s triangle wave. The oscillator’s triangular
waveform is compared to the ramping error amplifier voltage.
This generates PHASE pulses of increasing width that
charge the output capacitor(s). This interval of increasing
pulse width continues to t2. With sufficient output voltage,
the clamp on the reference input controls the output voltage.
This is the interval between t2 and t3 in Figure 3. At t3 the
SS voltage exceeds the reference voltage and the output
voltage is in regulation. This method provides a rapid and
controlled output voltage rise.
5
TIME (5ms/DIV)
FIGURE 3. SOFT-START INTERVAL
Over-Current Protection
The over-current function protects the converter from a
shorted output by using the upper MOSFET’s on-resistance,
r DS(ON) to monitor the current. This method enhances the
converter’s efficiency and reduces cost by eliminating a
current sensing resistor.
The over-current function cycles the soft-start function in a
hiccup mode to provide fault protection. A resistor (R OCSET )
programs the over-current trip level. An internal 200 μ A
(typical) current sink develops a voltage across R OCSET that
is reference to V IN . When the voltage across the upper
MOSFET (also referenced to V IN ) exceeds the voltage
across R OCSET , the over-current function initiates a soft-
start sequence. The soft-start function discharges C SS with
a 10 μ A current sink and inhibits PWM operation. The soft-
start function recharges C SS , and PWM operation resumes
with the error amplifier clamped to the SS voltage. Should an
overload occur while recharging C SS , the soft start function
inhibits PWM operation while fully charging C SS to 4V to
complete its cycle. Figure 4 shows this operation with an
overload condition. Note that the inductor current increases
to over 15A during the C SS charging interval and causes an
over-current trip. The converter dissipates very little power
with this method. The measured input power for the
conditions of Figure 4 is 2.5W.
4325.1
November 3, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| MC34268D | IC REG LDO 800MA 2.85V 8SOIC |
| EMC15DRAI-S734 | CONN EDGECARD 30POS .100 R/A PCB |
| RSM25DTKT-S288 | CONN EDGECARD 50POS .156 EXTEND |
| ACB20DHHR | CONN EDGECARD 40POS .050 DIP SLD |
| ABB20DHHR | CONN EDGECARD 40POS .050 DIP SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6013CB-T | 功能描述:IC CONTROLLER PWM BUCK 14-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 专用型 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,000 系列:- 应用:电源，ICERA E400，E450 输入电压:4.1 V ~ 5.5 V 输出数:10 输出电压:可编程 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:42-WFBGA，WLCSP 供应商设备封装:42-WLP 包装:带卷 (TR) |
| HIP6013CBZ | 功能描述:电压模式 PWM 控制器 STD BUCK PWM/1 5%/14 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6013CBZ-T | 功能描述:电压模式 PWM 控制器 STD BUCK PWM/1 5%/14 RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6014 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Buck and Synchronous-Rectifier (PWM) Controller and Output Voltage Monitor |
| HIP6014CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。