- 您现在的位置：买卖IC网 > PDF目录22314 > HIP6018BCB (Intersil)IC REG TRPL BCK/LINEAR 24-SOIC PDF资料下载
参数资料
| 型号： | HIP6018BCB |
| 厂商： | Intersil |
| 文件页数： | 13/15页 |
| 文件大小： | 384K |
| 描述： | IC REG TRPL BCK/LINEAR 24-SOIC |
| 标准包装： | 30 |
| 拓扑： | 降压（降压）同步（1），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 3 |
| 频率 - 开关： | 215kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 2.5V，- |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 3.3 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 24-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
13
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use ceramic capacitance
for the high frequency decoupling and bulk capacitors to
supply the RMS current. Small ceramic capacitors should be
placed very close to the upper MOSFET to suppress the
voltage induced in the parasitic circuit impedances.
For a through hole design, several electrolytic capacitors
(Panasonic HFQ series or Nichicon PL series or Sanyo MV-
GX or equivalent) may be needed. For surface mount
designs, solid tantalum capacitors can be used, but caution
must be exercised with regard to the capacitor surge current
rating. These capacitors must be capable of handling the
surge-current at power-up. The TPS series available from
AVX, and the 593D series from Sprague are both surge
current tested.
MOSFET Selection/Considerations
The HIP6018B requires 3 N-Channel power MOSFETs. Two
MOSFETs are used in the synchronous-rectified buck
topology of the PWM converter. The linear controller drives a
MOSFET as a pass transistor. These should be selected
based upon r
DS(ON)
, gate supply requirements, and thermal
management requirements.
PWM1 MOSFET Selection and Considerations
In high-current PWM applications, the MOSFET power
dissipation, package selection and heatsink are the dominant
design factors. The power dissipation includes two loss
components; conduction loss and switching loss. These losses
are distributed between the upper and lower MOSFETs
according to duty factor (see the equations below). The
conduction loss is the only component of power dissipation for
the lower MOSFET. Only the upper MOSFET has switching
losses, since the lower device turns on into near zero voltage.
The equations below assume linear voltage-current transitions
and do not model power loss due to the reverse-recovery of the
lower MOSFETs body diode. The gate-charge losses are
proportional to the switching frequency (F
S
) and are dissipated
by the HIP6018B, thus not contributing to the MOSFETs
temperature rise. However, large gate charge increases the
switching interval, t
SW
which increases the upper MOSFET
switching losses. Ensure that both MOSFETs are within their
maximum junction temperature at high ambient temperature by
calculating the temperature rise according to package thermal
resistance specifications. A separate heatsink may be
necessary depending upon MOSFET power, package type,
ambient temperature and air flow.
The r
DS(ON)
is different for the two previous equations even if the
type device is used for both. This is because the gate drive
applied to the upper MOSFET is different than the lower
MOSFET. Figure 14 shows the gate drive where the upper gate-
to-source voltage is approximately V
CC
less the input supply. For
+5V main power and +12VDC for the bias, the gate-to-source
voltage of Q1 is 7V. The lower gate drive voltage is +12VDC. A
logic-level MOSFET is a good choice for Q1 and a logic-level
MOSFET can be used for Q2 if its absolute gate-to-source
voltage rating exceeds the maximum voltage applied to V
CC
.
Rectifier CR1 is a clamp that catches the negative inductor
voltage swing during the dead time between the turn off of the
lower MOSFET and the turn on of the upper MOSFET. The
diode must be a Schottky type to prevent the lossy parasitic
MOSFET body diode from conducting. It is acceptable to omit
the diode and let the body diode of the lower MOSFET clamp
the negative inductor swing, but efficiency might drop one or
two percent as a result. The diode's rated reverse breakdown
voltage must be greater than twice the maximum input voltage.
Linear Controller MOSFET Selection
The main criteria for the selection of a transistor for the linear
regulator is package selection for efficient removal of heat.
The power dissipated in a linear regulator is:
Select a package and heatsink that maintains the junction
temperature below the maximum rating while operating at
the highest expected ambient temperature.
Additionally, if selecting a bipolar NPN transistor, insure the
gain (h
fe
) at the minimum operating temperature and given
collector-to-emitter voltage is sufficiently high as to deliver the
worst-case steady state current required by the GTL output,
when the transistor is driven with the minimum guaranteed
DRIVE3 output current. For example, operating at T junction
temperature, 3.3V input, and 1.5V output (V
CE
= 1.8V) the
NPNs gain should satisfy the following equation:
P
UPPER
I
O
2
r
DS ON
( )
?/DIV>
V
OUT
?/DIV>
V
IN
------------------------------------------------------------
I
O
V
IN
?nbsp t
SW
?nbsp F
S
?/DIV>
2
----------------------------------------------------
+
=
P
LOWER
I
O
2
r
DS ON
( )
?/DIV>
V
IN
V
OUT
(
)
?/DIV>
V
IN
---------------------------------------------------------------------------------
=
+12V
PGND
HIP6018B
GND
LGATE
UGATE
PHASE
V
CC
+5V OR LESS
NOTE:
NOTE:
V
GS
H V
CC
Q1
Q2
+
-
FIGURE 14. OUTPUT GATE DRIVERS
V
GS
H V
CC
-5V
CR1
P
LINEAR
I
O
V
IN
V
OUT
(
)
?/DIV>
=
h
fe
I
GTL
steady state
(
)
I
DRIVE3
min
( )
-----------------------------------------------------------
>
HIP6018B
相关PDF资料 |
PDF描述 |
|---|---|
| ECS-H1AD336R | CAP TANT 33UF 10V 20% 2917 |
| ISL6402IVZ-T | IC REG TRPL BCK/LINEAR 28TSSOP |
| ECS-H1AC156R | CAP TANT 15UF 10V 20% 2312 |
| ISL6534CR | IC REG TRPL BCK/LINEAR 32-QFN |
| EBC10DRYI | CONN EDGECARD 20POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6018BCB-T | 功能描述:IC REG TRPL BCK/LINEAR 24-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| HIP6018BCBZ | 功能描述:电压模式 PWM 控制器 ADV DL PWM "3 IN1" W/LWER DAC RNG RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6018BCBZ-T | 功能描述:电压模式 PWM 控制器 ADV DL PWM "3 IN1" W/LWER DAC RNG RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6018CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk 制造商:Harris Corporation 功能描述: |
| HIP6018CB-T | 制造商:Rochester Electronics LLC 功能描述:- Tape and Reel |
发布紧急采购，3分钟左右您将得到回复。