- 您现在的位置：买卖IC网 > PDF目录22314 > HIP6019BCB (Intersil)IC REG QD BCK/LINEAR 28-SOIC PDF资料下载
参数资料
| 型号： | HIP6019BCB |
| 厂商： | Intersil |
| 文件页数： | 6/15页 |
| 文件大小： | 0K |
| 描述： | IC REG QD BCK/LINEAR 28-SOIC |
| 标准包装： | 26 |
| 拓扑： | 降压（降压）同步（2），线性（LDO）（2） |
| 功能： | 任何功能 |
| 输出数： | 4 |
| 频率 - 开关： | 215kHz |
| 电压/电流 - 输出 1： | 控制器 |
| 电压/电流 - 输出 2： | 控制器 |
| 电压/电流 - 输出 3： | 控制器 |
| 带 LED 驱动器： | 无 |
| 带监控器： | 无 |
| 带序列发生器： | 无 |
| 电源电压： | 5 V ~ 12 V |
| 工作温度： | 0°C ~ 70°C |
| 安装类型： | * |
| 封装/外壳： | 28-SOIC（0.295"，7.50mm 宽） |
| 供应商设备封装： | * |
| 包装： | 管件 |
HIP6019B
I OCSET × R OCSET
I PEAK = ----------------------------------------------------
Functional Pin Description
VSEN1, VSEN2 (Pins 22 and 15)
These pins are connected to the PWM converters’ output
voltages. The PGOOD and OVP comparator circuits use
these signals to report output voltage status and for over-
voltage protection. VSEN2 provides the input power to the
integrated linear regulator.
OCSET1, OCSET2 (Pins 23 and 9)
Connect a resistor (R OCSET ) from this pin to the drain of the
respective upper MOSFET. R OCSET , an internal 200 μ A
current source (I OCSET ), and the upper MOSFET on-
resistance (r DS(ON) ) set the converter over-current (OC) trip
point according to the following equation:
r DS ( ON )
An over-current trip cycles the soft-start function. Sustaining an
over-current for 2 soft-start intervals shuts down the controller.
Additionally, OCSET1 is an output for the inverted FAULT
signal (FAULT). If a fault condition causes FAULT to go high,
OCSET1 will be simultaneously pulled to ground though an
internal MOS device (typical r DS(ON) = 100 ? ).
SS (Pin 12)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 11 μ A current source, sets the soft-
start interval of the converter. Pulling this pin low (typically
PHASE1, PHASE2 (Pins 26 and 2)
Connect the PHASE pins to the respective PWM converter’s
upper MOSFET source. These pins are used to monitor the
voltage drop across the upper MOSFETs for over-current
protection.
UGATE1, UGATE2 (Pins 27 and 1)
Connect UGATE pins to the respective PWM converter’s
upper MOSFET gate. These pins provide the gate drive for
the upper MOSFETs.
PGND (Pin 24)
This is the power ground connection. Tie the synchronous
PWM converter’s lower MOSFET source to this pin.
LGATE1 (Pin 25)
Connect LGATE1 to the synchronous PWM converter’s
lower MOSFET gate. This pin provides the gate drive for the
lower MOSFET.
VCC (Pin 28)
Provide a 12V bias supply for the IC to this pin. This pin also
provides the gate bias charge for all the MOSFETs
controlled by the IC.
FAULT/RT (Pin 13)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R T ) from this pin to GND, the nominal
200kHz switching frequency is increased according to the
following equation:
5 × 10
RT ( k ? )
below 1.0V) with an open drain signal will shutdown the IC.
VID0, VID1, VID2, VID3, VID4 (Pins 7, 6, 5, 4 and 3)
6
Fs ≈ 200kHz + ---------------------
(R T to GND)
VID0-4 are the input pins to the 5-bit DAC. The states of
these five pins program the internal voltage reference
(DACOUT). The level of DACOUT sets the core converter
output voltage (V OUT1 ). It also sets the core PGOOD and
Conversely, connecting a pull-up resistor (R T ) from this pin
to VCC reduces the switching frequency according to the
following equation:
4 × 10
RT ( k ? )
OVP thresholds.
COMP1, COMP2, and FB1, FB2
7
Fs ≈ 200kHz – ---------------------
(R T to 12V)
(Pins 20, 11, 21, and 10)
COMP1, 2 and FB1, 2 are the available external pins of the
PWM error amplifiers. Both the FB pins are the inverting
input of the error amplifiers. Similarly, the COMP pins are the
error amplifier outputs. These pins are used to compensate
the voltage-control feedback loops of the PWM converters.
GND (Pin 17)
Signal ground for the IC. All voltage levels are measured
with respect to this pin.
PGOOD (Pin 8)
PGOOD is an open collector output used to indicate the
status of the PWM converter output voltages. This pin is
pulled low when the core output is not within ± 10% of the
DACOUT reference voltage, or when any of the other
outputs are below their under-voltage thresholds. The
PGOOD output is open for ‘11111’ VID code. See Table 1.
6
Nominally, this pin voltage is 1.26V, but is pulled to VCC in
the event of an over-voltage or over-current condition.
GATE3 (Pin 18)
Connect this pin to the gate of an external MOSFET. This
pin provides the drive for the linear controller’s pass
transistor.
FB3 (Pin 19)
Connect this pin to a resistor divider to set the linear
controller output.
VOUT4 (Pin 16)
Output of the linear regulator. Supplies current up to 230mA.
FB4 (Pin 14)
Connect this pin to a resistor divider to set the linear
regulator output.
FN4587.1
April 13, 2005
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6018BCB-T | IC REG TRPL BCK/LINEAR 24-SOIC |
| MIC5822YN | IC DRVR LATCH 8BIT SER IN 16DIP |
| ECS-H1ED106R | CAP TANT 10UF 25V 20% 2917 |
| ECS-H1CD226R | CAP TANT 22UF 16V 20% 2917 |
| EEC15DRYI | CONN EDGECARD 30POS DIP .100 SLD |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6019BCB-T | 功能描述:IC REG QD BCK/LINEAR 28-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - 线性 + 切换式 系列:- 标准包装:2,500 系列:- 拓扑:降压（降压）同步（3），线性（LDO）（2） 功能:任何功能 输出数:5 频率 - 开关:300kHz 电压/电流 - 输出 1:控制器 电压/电流 - 输出 2:控制器 电压/电流 - 输出 3:控制器 带 LED 驱动器:无 带监控器:无 带序列发生器:是 电源电压:5.6 V ~ 24 V 工作温度:-40°C ~ 85°C 安装类型:* 封装/外壳:* 供应商设备封装:* 包装:* |
| HIP6019BCBZ | 功能描述:电压模式 PWM 控制器 ADV DL 3PWM & DL LINER PWR CONTROL RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6019BCBZ-T | 功能描述:电压模式 PWM 控制器 ADV DL 3PWM & DL LINER PWR CONTROL RoHS:否 制造商:Texas Instruments 输出端数量:1 拓扑结构:Buck 输出电压:34 V 输出电流: 开关频率: 工作电源电压:4.5 V to 5.5 V 电源电流:600 uA 最大工作温度:+ 125 C 最小工作温度:- 40 C 封装 / 箱体:WSON-8 封装:Reel |
| HIP6019BEVAL1 | 功能描述:电源管理IC开发工具 HIP6019B EVAL BRD FOR MB PWR MGMT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP6019CB | 制造商:Harris Corporation 功能描述: |
发布紧急采购，3分钟左右您将得到回复。