- 您现在的位置：买卖IC网 > PDF目录385382 > HIP6020ACB (INTERSIL CORP) Advanced Dual PWM and Dual Linear Power Controller PDF资料下载
参数资料
| 型号： | HIP6020ACB |
| 厂商： | INTERSIL CORP |
| 元件分类： | 稳压器 |
| 英文描述： | Advanced Dual PWM and Dual Linear Power Controller |
| 中文描述： | DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO28 |
| 封装： | PLASTIC, SOIC-28 |
| 文件页数： | 6/16页 |
| 文件大小： | 192K |
| 代理商： | HIP6020ACB |
4-6
Functional Pin Descriptions
VCC (Pin 28)
Provide a 12V bias supply for the IC to this pin. This pin also
provides the gate bias charge for all the MOSFETs
controlled by the IC. The voltage at this pin is monitored for
Power-On Reset (POR) purposes.
GND (Pin 17)
Signal ground for the IC. All voltage levels are measured with
respect to this pin.
PGND (Pin 24)
This is the power ground connection. Tie the synchronous
PWM converter’s lower MOSFET source to this pin.
VAUX (Pin 16)
The +3.3V input voltage at this pin is monitored for power-on
reset (POR) purposes. Connected to +5V input, this pin
provides boost current for the two linear regulator output
drives in the event bipolar NPN transistors (instead of
N-Channel MOSFETs) are employed as pass elements.
SS (Pin 12)
Connect a capacitor from this pin to ground. This capacitor,
along with an internal 28
μ
A current source, sets the
soft-start interval of the converter.
FAULT / RT (Pin 13)
This pin provides oscillator switching frequency adjustment.
By placing a resistor (R
T
) from this pin to GND, the nominal
200kHz switching frequency is increased according to the
following equation:
Conversely, connecting a pull-up resistor (R
T
) from this pin
to VCC reduces the switching frequency according to the
following equation:
Nominally, the voltage at this pin is 1.26V. In the event of an
over-voltage or over-current condition, this pin is internally
pulled to VCC.
PGOOD (Pin 8)
PGOOD is an open collector output used to indicate the
status of the output voltages. This pin is pulled low when the
synchronous regulator output is not within
±
10% of the
DACOUT reference voltage or when any of the other outputs
are below their under-voltage thresholds.
The PGOOD output is open for ‘11111’ VID code.
VID0, VID1, VID2, VID3, VID4 (Pins 7, 6, 5, 4 and 3)
VID0-4 are the TTL-compatible input pins to the 5-bit DAC.
The logic states of these five pins program the internal
voltage reference (DACOUT). The level of DACOUT sets the
microprocessor core converter output voltage, as well as the
coresponding PGOOD and OVP thresholds.
OCSET1, OCSET2 (Pins 23 and 9)
Connect a resistor (R
OCSET
) from this pin to the drain of the
respective upper MOSFET. R
OCSET
, an internal 200
μ
A
current source (I
OCSET
), and the upper MOSFET’s on-
resistance (r
DS(ON)
) set the converter over-current (OC) trip
point according to the following equation:
An over-current trip cycles the soft-start function.
The voltage at OCSET1 pin is monitored for power-on reset
(POR) purposes.
PHASE1, PHASE2 (Pins 26 and 2)
Connect the PHASE pins to the respective PWM converter’s
upper MOSFET source. These pins represent the gate drive
return current path and are used to monitor the voltage drop
across the upper MOSFETs for over-current protection.
UGATE1, UGATE2 (Pins 27 and 1)
Connect UGATE pins to the respective PWM converter’s
upper MOSFET gate. These pins provide the gate drive for
the upper MOSFETs. For SELECT high, UGATE2 is turned
on continuously to provide a DC current flow path to V
OUT2
.
LGATE1 (Pin 25)
Connect LGATE1 to the synchronous PWM converter’s
lower MOSFET gate. This pin provides the gate drive for the
lower MOSFET.
COMP1 and FB1 (Pins 20, and 21)
COMP1 and FB1 are the available external pins of the
synchronous PWM regulator error amplifier. The FB1 pin is
the inverting input of the error amplifier. Similarly, the
COMP1 pin is the error amplifier output. These pins are
used to compensate the voltage-mode control feedback loop
of the synchronous PWM converter.
VSEN1 (Pin 22)
This pin is connected to the synchronous PWM converters’
output voltage. The PGOOD and OVP comparator circuits
use this signal to report output voltage status and for over-
voltage protection.
VSEN2 (Pin 10)
Connect this pin to the output of the standard buck PWM
regulator. The voltage at this pin is regulated to 1.5V if the
SELECT pin is low. This pin is also monitored by the
PGOOD comparator circuit.
SELECT (Pin 11)
This pin determines the output voltage of the AGP bus
switching regulator. A low TTL input sets the output voltage
Fs
200KHz
T
6
)
--------------------
+
≈
(R
T
to GND)
Fs
200KHz
T
7
)
--------------------
–
≈
(R
T
to 12V)
I
PEAK
I
---------------------------------------------------
R
×
DS ON
)
=
HIP6020A
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6020EVAL1 | Advanced Dual PWM and Dual Linear Power Controller |
| HIP6020 | FPGA - 100000 SYSTEM GATE 2.5 VOLT - NOT RECOMMENDED for NEW DESIGN |
| HIP6020CB | Advanced Dual PWM and Dual Linear Power Controller |
| HIP6301VCBZ-T | 100000 SYSTEM GATE 1.8 VOLT FPGA - NOT RECOMMENDED for NEW DESIGN |
| HIP6301VCBZA | Microprocessor CORE Voltage Regulator Multi-Phase Buck PWM Controller |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6020ACB WAF | 制造商:Harris Corporation 功能描述: |
| HIP6020ACB-T | 制造商:Rochester Electronics LLC 功能描述:DUAL PWM AND 2 LINEAR CONTROLLER W/O VID=11111 SHUTDOWN - Tape and Reel |
| HIP6020CB | 制造商:Rochester Electronics LLC 功能描述:DUAL PWM AND 2 LINEAR CONTROLLER - Bulk |
| HIP6020CB-T | 制造商:Rochester Electronics LLC 功能描述:DUAL PWM AND 2 LINEAR CONTROLLER TAPE AND REEL - Tape and Reel |
| HIP6020EVAL1 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Advanced Dual PWM and Dual Linear Power Controller |
发布紧急采购，3分钟左右您将得到回复。