- 您现在的位置：买卖IC网 > PDF目录15074 > HIP6311CB (Intersil)IC REG CTRLR BUCK PWM 20-SOIC PDF资料下载
参数资料
| 型号： | HIP6311CB |
| 厂商： | Intersil |
| 文件页数： | 8/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-SOIC |
| 标准包装： | 38 |
| PWM 型： | 控制器 |
| 输出数： | 4 |
| 频率 - 最大： | 305kHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
HIP6311
than the average current, the signal applied via the summing
Correction circuit to the Comparator, reduces the output
pulse width of the Comparator to compensate for the
detected “above average” current in that channel.
Droop Compensation
In addition to control of each power channel’s output current,
the average channel current is also used to provide CORE
voltage “droop” compensation. Average full channel current
is defined as 50 μ A. By selecting an input resistor, R IN , the
amount of voltage droop required at full load current can be
programmed. The average current driven into the FB pin
results in a voltage increase across resistor R IN that is in the
direction to make the Error Amplifier “see” a higher voltage
at the inverting input, resulting in the Error Amplifier
adjusting the output voltage lower. The voltage developed
across R IN is equal to the “droop” voltage. See the “Current
Sensing and Balancing” section for more details.
Applications and Convertor Start-Up
Each PWM power channel’s current is regulated. This
enables the PWM channels to accurately share the load
current for enhanced reliability. The HIP6601, HIP6602 or
HIP6603 MOSFET driver interfaces with the HIP6311. For
more information, see the HIP6601, HIP6602 or HIP6603
data sheets.
The HIP6311 is capable of controlling up to 4 PWM power
channels. Connecting unused PWM outputs to V CC
automatically sets the number of channels. The phase
relationship between the channels is 360 o /number of active
PWM channels. For example, for three channel operation,
the PWM outputs are separated by 120 o . Figure 2 shows the
PWM output signals for a four channel system.
PWM 1
PWM 2
PWM 3
PWM 4
FIGURE 2. FOUR PHASE PWM OUTPUT AT 500kHz
Power supply ripple frequency is determined by the channel
frequency, F SW , multiplied by the number of active channels.
8
For example, if the channel frequency is set to 250kHz and
there are three phases, the ripple frequency is 750kHz.
The IC monitors and precisely regulates the CORE voltage
of a microprocessor. After initial start-up, the controller also
provides protection for the load and the power supply. The
following section discusses these features.
Initialization
The HIP6311 usually operates from an ATX power supply.
Many functions are initiated by the rising supply voltage to the
V CC pin of the HIP6311. Oscillator, Sawtooth Generator, Soft-
Start and other functions are initialized during this interval.
These circuits are controlled by POR, Power-On Reset. During
this interval, the PWM outputs are driven to a three state
condition that makes these outputs essentially open. This state
results in no gate drive to the output MOSFETs.
Once the V CC voltage reaches 4.375V (+125mV), a voltage
level to insure proper internal function, the PWM outputs are
enabled and the Soft-Start sequence is initiated. If for any
reason, the V CC voltage drops below 3.875V (+125mV). the
POR circuit shuts the converter down and again three states
the PWM outputs.
Soft-Start
After the POR function is completed with V CC reaching
4.375V, the Soft-Start sequence is initiated. Soft-Start, by its
slow rise in CORE voltage from zero, avoids an over-current
condition by slowly charging the discharged output
capacitors. This voltage rise is initiated by an internal DAC
that slowly raises the reference voltage to the error amplifier
input. The voltage rise is controlled by the oscillator
frequency and the DAC within the HIP6311, therefore, the
output voltage is effectively regulated as it rises to the final
programmed CORE voltage value.
For the first 32 PWM switching cycles, the DAC output
remains inhibited and the PWM outputs remain three stated.
From the 33rd cycle and for another, approximately 150
cycles the PWM output remains low, clamping the lower
output MOSFETs to ground, see Figure 3. The time variability
is due to the Error Amplifier, Sawtooth Generator and
Comparators moving into their active regions. After this short
interval, the PWM outputs are enabled and increment the
PWM pulse width from zero duty cycle to operational pulse
width, thus allowing the output voltage to slowly reach the
CORE voltage. The CORE voltage will reach its programmed
value before the 2048 cycles, but the PGOOD output will not
be initiated until the 2048th PWM switching cycle.
The Soft-Start time or delay time, DT = 2048/F SW . For an
oscillator frequency, F SW , of 200kHz, the first 32 cycles or
160 μ s, the PWM outputs are held in a three state level as
explained above. After this period and a short interval
described above, the PWM outputs are initiated and the
voltage rises in 10.08ms, for a total delay time DT of
10.24ms.
FN4817.3
December 27, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| RCC22DREN-S93 | CONN EDGECARD 44POS .100 EYELET |
| HIP6311ACB | IC REG CTRLR BUCK PWM 20-SOIC |
| X5165S8IZ | IC CPU SUPERV 16K EEPROM 8-SOIC |
| HIP6302VCB | IC REG CTRLR BUCK PWM 16-SOIC |
| HIP6301VCB-T | IC REG CTRLR BUCK PWM 20-SOIC |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6311CB-T | 功能描述:IC REG CTRLR BUCK PWM 20-SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 稳压器 - DC DC 切换控制器 系列:- 标准包装:4,000 系列:- PWM 型:电压模式 输出数:1 频率 - 最大:1.5MHz 占空比:66.7% 电源电压:4.75 V ~ 5.25 V 降压:是 升压:无 回扫:无 反相:无 倍增器:无 除法器:无 Cuk:无 隔离:无 工作温度:-40°C ~ 85°C 封装/外壳:40-VFQFN 裸露焊盘 包装:带卷 (TR) |
| HIP6311CBZ | 功能描述:电流型 PWM 控制器 2-4 PHS SYNCH BUCK CNTRLR 0 8%F RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6311CBZA | 功能描述:电流型 PWM 控制器 W/ANL 2-4 PHS SYNCH BUCK CNTRLR 0 8%F RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6311CBZA-T | 功能描述:电流型 PWM 控制器 W/ANL 2-4 PHS SYNCH BUCK CNTRLR 0 8%F RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6311CBZ-T | 功能描述:电流型 PWM 控制器 2-4 PHS SYNCH BUCK CNTRLR 0 8%REF TAPE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
发布紧急采购，3分钟左右您将得到回复。