- 您现在的位置：买卖IC网 > PDF目录15158 > HIP6311CBZA (Intersil)IC REG CTRLR BUCK PWM 20-SOIC PDF资料下载
参数资料
| 型号： | HIP6311CBZA |
| 厂商： | Intersil |
| 文件页数： | 13/17页 |
| 文件大小： | 0K |
| 描述： | IC REG CTRLR BUCK PWM 20-SOIC |
| 标准包装： | 380 |
| PWM 型： | 控制器 |
| 输出数： | 4 |
| 频率 - 最大： | 305kHz |
| 电源电压： | 4.75 V ~ 5.25 V |
| 降压： | 是 |
| 升压： | 无 |
| 回扫： | 无 |
| 反相： | 无 |
| 倍增器： | 无 |
| 除法器： | 无 |
| Cuk： | 无 |
| 隔离： | 无 |
| 工作温度： | 0°C ~ 70°C |
| 封装/外壳： | 20-SOIC（0.295"，7.50mm 宽） |
| 包装： | 管件 |
HIP6311
average current per phase. Neglecting secondary effects,
the sampled current (I SAMPLE ) can be related to the load
current (I LT ) by:
I SAMPLE = I LT / n + (V IN V CORE - 3V CORE2 ) / (6L x F SW x
V IN )
Where: I LT = total load current
n = the number of channels
Example: Using the previously given conditions, and
For I LT = 100A,
n =4
Then I SAMPLE = 25.49A
As discussed previously, the voltage drop across each Q2
transistor at the point in time when current is sampled is
1,000
500
200
100
50
20
10
5
r DSON (Q2) x I SAMPLE . The voltage at Q2’s drain, the
PHASE node, is applied through the R ISEN resistor to the
HIP6311 ISEN pin. This pin is held at virtual ground, so the
current into ISEN is:
2
1
10
20
50
100
200
500 1,000 2,000 5,000 10,000
I SENSE = I SAMPLE x r DS(ON) (Q2) / R ISEN .
CHANNEL OSCILLATOR FREQUENCY, F SW (kHz)
R Isen
= I SAMPLE x r DS(ON) (Q2) / 50 μ A
FIGURE 10. RESISTANCE R T vs FREQUENCY
Example: From the previous conditions,
Layout Considerations
where I LT
I SAMPLE
r DS(ON) (Q2)
Then: R ISEN
I CURRENT TRIP
Short circuit I LT
= 100A,
= 25.49A,
= 4m ?
= 2.04K and
= 165%
= 165A.
MOSFETs switch very fast and efficiently. The speed with
which the current transitions from one device to another
causes voltage spikes across the interconnecting
impedances and parasitic circuit elements. These voltage
spikes can degrade efficiency, radiate noise into the circuit
and lead to device over-voltage stress. Careful component
layout and printed circuit design minimizes the voltage
spikes in the converter. Consider, as an example, the turnoff
transition of the upper PWM MOSFET. Prior to turnoff, the
Channel Frequency Oscillator
The channel oscillator frequency is set by placing a resistor,
R T , to ground from the FS/DIS pin. Figure 10 is a curve
showing the relationship between frequency, F SW , and
resistor R T . To avoid pickup by the FS/DIS pin, it is important
to place this resistor next to the pin. If this pin is also used to
disable the converter, it is also important to locate the pull-
down device next to this pin.
13
upper MOSFET was carrying channel current. During the
turnoff, current stops flowing in the upper MOSFET and is
picked up by the lower MOSFET. Any inductance in the
switched current path generates a large voltage spike during
the switching interval. Careful component selection, tight
layout of the critical components, and short, wide circuit
traces minimize the magnitude of voltage spikes. Contact
Intersil for evaluation board drawings of the component
placement and printed circuit board.
There are two sets of critical components in a DC-DC
converter using a HIP6311 controller and a HIP6601 gate
driver. The power components are the most critical because
they switch large amounts of energy. Next are small signal
components that connect to sensitive nodes or supply critical
bypassing current and signal coupling.
The power components should be placed first. Locate the
input capacitors close to the power switches. Minimize the
length of the connections between the input capacitors, C IN ,
and the power switches. Locate the output inductors and
output capacitors between the MOSFETs and the load.
Locate the gate driver close to the MOSFETs.
FN4817.3
December 27, 2004
相关PDF资料 |
PDF描述 |
|---|---|
| VE-J5W-EY-F3 | CONVERTER MOD DC/DC 5.5V 50W |
| VE-BTW-EV-F2 | CONVERTER MOD DC/DC 5.5V 150W |
| HIP6311CBZ | IC REG CTRLR BUCK PWM 20-SOIC |
| CAT1025ZI-42-GT3 | IC SUPERVISOR CPU 2K EEPR 8MSOP |
| VE-J5R-EY-F3 | CONVERTER MOD DC/DC 7.5V 50W |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6311CBZA-T | 功能描述:电流型 PWM 控制器 W/ANL 2-4 PHS SYNCH BUCK CNTRLR 0 8%F RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6311CBZ-T | 功能描述:电流型 PWM 控制器 2-4 PHS SYNCH BUCK CNTRLR 0 8%REF TAPE RoHS:否 制造商:Texas Instruments 开关频率:27 KHz 上升时间: 下降时间: 工作电源电压:6 V to 15 V 工作电源电流:1.5 mA 输出端数量:1 最大工作温度:+ 105 C 安装风格:SMD/SMT 封装 / 箱体:TSSOP-14 |
| HIP6311VCB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
| HIP6312VACB | 制造商:Intersil Corporation 功能描述: |
| HIP6500 | 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Multiple Linear Power Controller with ACPI Control Interface |
发布紧急采购，3分钟左右您将得到回复。