参数资料
型号: HIP6501
厂商: Intersil Corporation
元件分类: 基准电压源/电流源
英文描述: Triple Linear Power Controller with ACPI Control Interface
中文描述: 三线性电源控制器ACPI控制接口
文件页数: 8/14页
文件大小: 140K
代理商: HIP6501
8
Soft-Start Circuit
Soft-Start into Sleep States (S3, S4/S5)
The 5VSB POR function initiates the soft-start sequence. An
internal 10
μ
A current source charges an external capacitor
to 5V. The error amplifiers reference inputs are clamped to a
level proportional to the SS (Soft-Start) pin voltage. As the
SS pin voltage slews from about 1.25V to 2.5V, the input
clamp allows a rapid and controlled output voltage rise.
Figure 9 shows the soft-start sequence for the typical
application start-up in a sleep state with all output voltages
enabled. At time T0 5V
SB
(bias) is applied to the circuit. At
time T1, 5V
SB
surpasses POR level, and an internal fast
charge circuit quickly raises the SS capacitor voltage to
approximately 1V. At this point, the 10
μ
A current source
continues the charging up to T2, where a voltage of 1.25V
(typically) is reached and an internal clamp limits further
charging. Clamping of the soft-start voltage (T2 to T3
interval) should only be noticed with capacitors smaller than
0.1
μ
F; soft-start capacitors of 0.1
μ
F and above should
present a soft-start ramp void of this plateau. At time T3,
3ms (typically) past the 5V
SB
POR (T1), the memory output
voltage selection is latched in and the charging of the soft-
start capacitor resumes, using the 10
μ
A current source. At
this point, the error amplifiers’ reference inputs are starting
their transitions, causing the output voltages to ramp up
proportionally. The ramping continues until time T4 when all
the voltages reach the set value. At time T5, when the soft-
start capacitor value reaches approximately 2.8V, the under-
voltage monitoring circuits are activated and the soft-start
capacitor is quickly discharged down to the value attained at
time T2 (approximately 1.25V).
FIGURE 6. 3V
DUAL
AND 5V
DUAL
TIMING DIAGRAM FOR
EN3VDL = 0, EN5VDL = 1
FIGURE 7. 3V
DUAL
AND 5V
DUAL
TIMING DIAGRAM FOR
EN3VDL = 0, EN5VDL = 0
FIGURE 8. 2.5/3.3V
MEM
TIMING DIAGRAM
5VSB
12V
S3
S5
5VDLSB
DLA
3V3DLSB
3V3DL
5VDL
5VSB
12V
S3
S5
5VDLSB
DLA
3V3DLSB
3V3DL
5VDL
5VSB
12V
S3
S5
DRV2
DEVICE
VSEN2
INTVSEN2
FIGURE 9. SOFT-START INTERVAL IN A SLEEP STATE (ALL
OUTPUTS ENABLED)
0V
0V
TIME
SOFT-START
(1V/DIV)
OUTPUT
VOLTAGES
(1V/DIV)
V
OUT1
(3.3V
DUAL
)
V
OUT2
(2.5V
MEM
)
V
OUT3
(5V
DUAL
)
T1 T2T3
T0
5VSB
(1V/DIV)
UV DETECT ENABLE
(LOGIC LEVEL)
T5
T4
HIP6501A
相关PDF资料
PDF描述
HIP6501A Triple Linear Power Controller with ACPI Control Interface(带ACPI控制接口的线性电源控制器)
HIP6501EVAL1 Triple Linear Power Controller with ACPI Control Interface
HIP6501ACB Triple Linear Power Controller with ACPI Control Interface
HIP6521 PWM and Triple Linear Power Controller
HIP6521CB PWM and Triple Linear Power Controller
相关代理商/技术参数
参数描述
HIP6501A 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface
HIP6501A_04 制造商:INTERSIL 制造商全称:Intersil Corporation 功能描述:Triple Linear Power Controller with ACPI Control Interface
HIP6501ACB 功能描述:IC PWM TRIPLE POWER CTRLR 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器,监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(5x5) 包装:带卷 (TR)
HIP6501ACB-T 功能描述:IC PWM TRIPLE POWER CTRLR 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器,监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP(5x5) 包装:带卷 (TR)
HIP6501ACBZ 功能描述:PMIC 解决方案 COMPANION CHIP TO HI6020/21 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel