- 您现在的位置：买卖IC网 > PDF目录371822 > HIP6501ACB (INTERSIL CORP) Triple Linear Power Controller with ACPI Control Interface PDF资料下载
参数资料
| 型号： | HIP6501ACB |
| 厂商： | INTERSIL CORP |
| 元件分类： | 电源管理 |
| 英文描述： | Triple Linear Power Controller with ACPI Control Interface |
| 中文描述： | 4-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO16 |
| 封装： | PLASTIC, MS-012-AC, SOIC-16 |
| 文件页数： | 8/14页 |
| 文件大小： | 140K |
| 代理商： | HIP6501ACB |
8
Soft-Start Circuit
Soft-Start into Sleep States (S3, S4/S5)
The 5VSB POR function initiates the soft-start sequence. An
internal 10
μ
A current source charges an external capacitor
to 5V. The error amplifiers reference inputs are clamped to a
level proportional to the SS (Soft-Start) pin voltage. As the
SS pin voltage slews from about 1.25V to 2.5V, the input
clamp allows a rapid and controlled output voltage rise.
Figure 9 shows the soft-start sequence for the typical
application start-up in a sleep state with all output voltages
enabled. At time T0 5V
SB
(bias) is applied to the circuit. At
time T1, 5V
SB
surpasses POR level, and an internal fast
charge circuit quickly raises the SS capacitor voltage to
approximately 1V. At this point, the 10
μ
A current source
continues the charging up to T2, where a voltage of 1.25V
(typically) is reached and an internal clamp limits further
charging. Clamping of the soft-start voltage (T2 to T3
interval) should only be noticed with capacitors smaller than
0.1
μ
F; soft-start capacitors of 0.1
μ
F and above should
present a soft-start ramp void of this plateau. At time T3,
3ms (typically) past the 5V
SB
POR (T1), the memory output
voltage selection is latched in and the charging of the soft-
start capacitor resumes, using the 10
μ
A current source. At
this point, the error amplifiers’ reference inputs are starting
their transitions, causing the output voltages to ramp up
proportionally. The ramping continues until time T4 when all
the voltages reach the set value. At time T5, when the soft-
start capacitor value reaches approximately 2.8V, the under-
voltage monitoring circuits are activated and the soft-start
capacitor is quickly discharged down to the value attained at
time T2 (approximately 1.25V).
FIGURE 6. 3V
DUAL
AND 5V
DUAL
TIMING DIAGRAM FOR
EN3VDL = 0, EN5VDL = 1
FIGURE 7. 3V
DUAL
AND 5V
DUAL
TIMING DIAGRAM FOR
EN3VDL = 0, EN5VDL = 0
FIGURE 8. 2.5/3.3V
MEM
TIMING DIAGRAM
5VSB
12V
S3
S5
5VDLSB
DLA
3V3DLSB
3V3DL
5VDL
5VSB
12V
S3
S5
5VDLSB
DLA
3V3DLSB
3V3DL
5VDL
5VSB
12V
S3
S5
DRV2
DEVICE
VSEN2
INTVSEN2
FIGURE 9. SOFT-START INTERVAL IN A SLEEP STATE (ALL
OUTPUTS ENABLED)
0V
0V
TIME
SOFT-START
(1V/DIV)
OUTPUT
VOLTAGES
(1V/DIV)
V
OUT1
(3.3V
DUAL
)
V
OUT2
(2.5V
MEM
)
V
OUT3
(5V
DUAL
)
T1 T2T3
T0
5VSB
(1V/DIV)
UV DETECT ENABLE
(LOGIC LEVEL)
T5
T4
HIP6501A
相关PDF资料 |
PDF描述 |
|---|---|
| HIP6521 | PWM and Triple Linear Power Controller |
| HIP6521CB | PWM and Triple Linear Power Controller |
| HIP6521EVAL1 | PWM and Triple Linear Power Controller |
| HIP6602BCRZ-T | Dual Channel Synchronous Rectified Buck MOSFET Driver |
| HIP6602BCRZA | Dual Channel Synchronous Rectified Buck MOSFET Driver |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HIP6501ACB-T | 功能描述:IC PWM TRIPLE POWER CTRLR 16SOIC RoHS:否 类别:集成电路 (IC) >> PMIC - 电源控制器，监视器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:2,500 系列:- 应用:多相控制器 输入电压:- 电源电压:9 V ~ 14 V 电流 - 电源:- 工作温度:-40°C ~ 85°C 安装类型:表面贴装 封装/外壳:40-WFQFN 裸露焊盘 供应商设备封装:40-TQFN-EP（5x5） 包装:带卷 (TR) |
| HIP6501ACBZ | 功能描述:PMIC 解决方案 COMPANION CHIP TO HI6020/21 RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| HIP6501ACBZ-T | 功能描述:PMIC 解决方案 COMPANION CHIP TO HIP60/21 TAPE/REEL RoHS:否 制造商:Texas Instruments 安装风格:SMD/SMT 封装 / 箱体:QFN-24 封装:Reel |
| HIP6501AEVAL1 | 功能描述:电源管理IC开发工具 HIP6501A EVAL BRD FOR ACPI PWR MGT RoHS:否 制造商:Maxim Integrated 产品:Evaluation Kits 类型:Battery Management 工具用于评估:MAX17710GB 输入电压: 输出电压:1.8 V |
| HIP6501CB | 制造商:Rochester Electronics LLC 功能描述:- Bulk |
发布紧急采购，3分钟左右您将得到回复。