- 您现在的位置：买卖IC网 > PDF目录60838 > HMC566 (HITTITE MICROWAVE CORP) 29000 MHz - 36000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER PDF资料下载
参数资料
| 型号： | HMC566 |
| 厂商： | HITTITE MICROWAVE CORP |
| 元件分类： | 放大器 |
| 英文描述： | 29000 MHz - 36000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| 封装： | 2.54 X 0.98 MM, 0.10 MM HEIGHT, DIE-6 |
| 文件页数： | 6/6页 |
| 文件大小： | 241K |
| 代理商： | HMC566 |
L
O
W
N
O
IS
E
A
M
P
L
IF
IE
RS
-
C
H
IP
1
1 - 95
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should be
raised 0.150mm (6 mils) so that the surface of the die is coplanar with the surface
of the substrate. One way to accomplish this is to attach the 0.102mm (4 mil) thick
die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab) which is then
attached to the ground plane (Figure 2).
Microstrip substrates should be brought as close to the die as possible in order to
minimize bond wire length. Typical die-to-substrate spacing is 0.076mm (3 mils).
Handling Precautions
Follow these precautions to avoid permanent damage.
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
Static Sensitivity:
Follow ESD precautions to protect against > ± 250V ESD
strikes.
Transients: Suppress instrument and bias supply transients while bias is applied.
Use shielded signal and bias cables to minimize inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with
a sharp pair of bent tweezers. The surface of the chip has fragile air bridges and
should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms
or with electrically conductive epoxy. The mounting surface should be clean and
flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 °C and a tool temperature
of 265 °C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 °C. DO NOT expose the chip
to a temperature greater than 320 °C for more than 20 seconds. No more than 3 seconds of scrubbing should be required for
attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025 mm (1 mil) diameter pure gold wire is recommended. Thermosonic wirebonding with a nominal stage
temperature of 150 °C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use
the minimum level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on
the package or substrate. All bonds should be as short as possible <0.31 mm (12 mils).
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Wire Bond
RF Ground Plane
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
0.076mm
(0.003”)
Figure 2.
0.150mm (0.005”) Thick
Moly Tab
HMC566
GaAs PHEMT MMIC LOW NOISE
AMPLIFIER, 29 - 36 GHz
v00.0306
相关PDF资料 |
PDF描述 |
|---|---|
| HMC568LC5 | RF/MICROWAVE DOWN CONVERTER |
| HMC576LC3B | 9000 MHz - 14500 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| HMC577LC4B | 27000 MHz - 31000 MHz RF/MICROWAVE FREQUENCY DOUBLER |
| HMC589ST89E | 0 MHz - 4000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
| HMC589ST89 | 0 MHz - 4000 MHz RF/MICROWAVE WIDE BAND LOW POWER AMPLIFIER |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HMC566_09 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs PHEMT MMIC LOW NOISE AMPLIFIER, 29 - 36 GHz |
| HMC566LP4_09 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 28 - 36 GHz |
| HMC566LP4E | 制造商:Hittite Microwave Corp 功能描述:IC AMP MMIC LNA PHEMT 24QFN |
| HMC566LP4E_10 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs pHEMT MMIC LOW NOISE AMPLIFIER, 28 - 36 GHz |
| HMC567LC5 | 制造商:HITTITE 制造商全称:Hittite Microwave Corporation 功能描述:GaAs MMIC I/Q DOWNCONVERTER 7 - 9 GHz |
发布紧急采购，3分钟左右您将得到回复。