参数资料
型号: HMR2300-D20-232
厂商: Honeywell Microelectronics & Precision Sensors
文件页数: 6/12页
文件大小: 0K
描述: MAGNETOMETER RS232 W/CASE
产品培训模块: Magnetic Sensors
标准包装: 1
系列: HMR
轴: X,Y,Z
测量范围: ±2 高斯
用于测量: 磁场强度,方向
分辨率: 67 µ高斯
类型: 数字磁力计
封装/外壳: 带外壳的模块
接口: RS-232,RS-485
产品目录页面: 2813 (CN2011-ZH PDF)
配用: 342-1012-ND - KIT DEVELOP MAGNETOMETER RS232
其它名称: 342-1015
HMR2300
RS-485 BALANCED I/O INTERCONNECTS
HOST PC
A-
D
R
Z
B+
Z
Z = 120 ohms
RD(A)
TD(B)
R
D
HMR2300
ID = 01
RD(A)
TD(B)
R
D
HMR2300
ID = 02
DATA COMMUNICATIONS
The RS-232 signals are single-ended undirectional levels that are sent received simultaneously (full duplex). One signal is
from the host personal computer (PC) transmit (TD) to the HMR2300 receive (RD) data line, and the other is from the
HMR2300 TD to the PC RD data line. When a logic one is sent, either the TD or RD line will drive to about +6 Volts
referenced to ground. For a logic zero, the TD or RD line will drive to about – 6 Volts below ground. Since the signals are
transmitted and dependent on an absolute voltage level, this limits the distance of transmission due to line noise and
signal to about 60 feet.
When using RS-485, the signals are balanced differential transmissions sharing the same lines (half-duplex). This means
that logic one the transmitting end will drive the B line at least 1.5 Volts higher than the A line. For a logic zero, the
transmitting end will drive the B line at least 1.5 Volts lower than the A line. Since the signals are transmitted as difference
voltage level, these signals can withstand high noise environments or over very long distances where line loss may be a
problem; up to 4000 feet. Note that long RS-485 lines should be terminated at both ends with 120-ohm resistors.
Another precaution on RS-485 operation is that when the HMR2300 is in a continuous output mode of operation, the host
PC may have to send repeated escape and carriage return bytes to stop the stream of output data. If the host can detect
a recieved carriage return byte (0D hex), and immediately send the escape-carriage return bytes; then a systematic stop
of continuous output is likely. If manually sent, beware that the half-duplex nature of the interface corrupt the HMR2300
outbound data while attempting to get the stop command interleaved between the data.
As noted by the Digital I/O timing specification and Figure 3, the HMR2300 has a delayed response feature based on the
programmed device ID in response to global address commands (*99….<cr>). Each HMR2300 will take its turn
responding so that units do not transmit simultaneously (no contension). These delays also apply to the RS-232 interface
versions of the HMR2300.
6
www.honeywell.com
相关PDF资料
PDF描述
D2MV-1L-1C2 BASIC SWITCH
HMR2300-D00-232 MAGNETOMETER RS232
HMR2300-D21-485 MAGNETOMETER RS485 W/CASE
HSP50210JC-52Z IC DEMODULATOR COSTAS 84-PLCC
HMR2300-D20-485 MAGNETOMETER RS485 W/CASE
相关代理商/技术参数
参数描述
HMR2300-D20-485 功能描述:MAGNETOMETER RS485 W/CASE RoHS:否 类别:传感器,转换器 >> 磁性 - 罗盘,磁场(模块) 系列:HMR 标准包装:490 系列:- 轴:X,Y,Z 测量范围:±1.3 ~ 8.1高斯,±2,4,8高斯 用于测量:制导,间距和卷 分辨率:8 毫高斯 类型:数字罗盘 封装/外壳:28-VFLGA 接口:I²C 配用:497-10689-ND - BOARD ADAPTER LSM303DLH DIL24 其它名称:497-10474
HMR2300-D21-232 功能描述:MAGNETOMETER RS232 W/CASE RoHS:否 类别:传感器,转换器 >> 磁性 - 罗盘,磁场(模块) 系列:HMR 标准包装:490 系列:- 轴:X,Y,Z 测量范围:±1.3 ~ 8.1高斯,±2,4,8高斯 用于测量:制导,间距和卷 分辨率:8 毫高斯 类型:数字罗盘 封装/外壳:28-VFLGA 接口:I²C 配用:497-10689-ND - BOARD ADAPTER LSM303DLH DIL24 其它名称:497-10474
HMR2300-D21-232-DEMO 功能描述:KIT DEVELOP MAGNETOMETER RS232 RoHS:否 类别:编程器,开发系统 >> 评估板 - 传感器 系列:- 产品培训模块:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 标准包装:1 系列:-
HMR2300-D21-485 功能描述:MAGNETOMETER RS485 W/CASE RoHS:否 类别:传感器,转换器 >> 磁性 - 罗盘,磁场(模块) 系列:HMR 标准包装:490 系列:- 轴:X,Y,Z 测量范围:±1.3 ~ 8.1高斯,±2,4,8高斯 用于测量:制导,间距和卷 分辨率:8 毫高斯 类型:数字罗盘 封装/外壳:28-VFLGA 接口:I²C 配用:497-10689-ND - BOARD ADAPTER LSM303DLH DIL24 其它名称:497-10474
HMR2300R 制造商:HONEYWELL 制造商全称:Honeywell Solid State Electronics Center 功能描述:THREE-AXIS STRAPDOWN MAGNETOMETER