- 您现在的位置：买卖IC网 > PDF目录10636 > HR10A-10J-10S (Hirose Electric Co Ltd)HR10A, JACK, 10 POS W/SOCKET PDF资料下载
参数资料
| 型号： | HR10A-10J-10S |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 11/20页 |
| 文件大小： | 0K |
| 描述： | HR10A, JACK, 10 POS W/SOCKET |
| 标准包装： | 20 |
| 系列： | HR10A |
| 连接器类型： | 插孔，母插口 |
| 位置数： | 10 |
| 外壳尺寸 - 插件： | 10 |
| 安装类型： | 自由悬挂 |
| 端子： | 焊接 |
| 紧固型： | 推挽式 |
| 方向： | 带标记 |
| 外壳材料，表面处理： | 黄铜和锌，镀镍 |
| 触点表面涂层： | 银 |
| 包装： | 散装 |
| 额定电流： | 2A |
| 工作温度： | -25°C ~ 85°C |
| 其它名称： | *HR10A-10J-10S HR316 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
HR10 Series ● Push-Pull Connectors
■ Cable connecting methods
HR10B-2.5CP
HR10B-2.5CJ
1.Cable end treatment
3.Crimping cable outer conductor
Fig.1
11±0.5
Fig.3
(HR10B-2.5CP)
A
1.4±0.2
(2.5) 3.7±0.2
Slit cable outer jaket
2 pieces (180° reverse side)
Clamp metal
Connector
Remove excess insulator
material (remaining after
clamping is complated)
with a knife or aimilarobject.
1.Dimensions for cable end treatment are shown in
Table 1 dimenshion A
Fig 1.
2.Termination is described below.
(1).Strip cable outer jacket as indicated.
2.5CP
1.5±0.2mm
2.5CJ
0 +0.3 mm
(2).Slit outer jacket on both sides per Fig.1.
(3).Fold back outer cover.
(4).Remove insulator from cable.
2.Soldering male pin to cable center
conductor.
Fig.2
Malu pin or Female pin
Soldering
1. Insert cable prepared per PROCESS 2 into the
connector.The cable should be inserted until it
comes to a full stop.This may be verified by
checking the dimension from the side of the
connector to the top of the contact(as indicated in
Fig 3). This dimension should be A.
2. Crimp this installed metal clamp with tool HR10-
TC-01 per Fig.3 and remove excess insulation with
a knife.
It is possible to pull back the contact.
Hold cable when crimping metal clamp and keep
the dimension to show in Fig 3. after crimping metal
clamp.
Should fix flush
Contact fixing jig
such as vise
1.Solder male pin to cable center conductor as
indicated in Fig.2.
(1).Pre-solder the solder pot of pin with ? 0.5mm
string solder.
(2).Male pin should fit flush against the cable
insulator as shown.
(3).Remove any excess solder from the pin with a
knife.This surface must be smooth.
(4).A properly soldered terminal will yield 500gf
when stretched.
189
相关PDF资料 |
PDF描述 |
|---|---|
| VE-BWP-MX-F2 | CONVERTER MOD DC/DC 13.8V 75W |
| MAX3040ESE+ | IC RS485/422 TRANS QUAD 16-SOIC |
| VE-BWN-MX-F3 | CONVERTER MOD DC/DC 18.5V 75W |
| MAX3041EUE+ | IC RS485/422 TRANS QUAD 16TSSOP |
| NCS2202SN2T1 | IC COMPARATOR LV LOW PWR 5TSOP |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HR10A-10J-10S(01) | 制造商:Hirose 功能描述:CONN JACK 10POS FEMALE SLD GOLD |
| HR10A-10J-10S(73) | 功能描述:环形推拉式连接器 10P JACK SHELL SZ 10 FEMALE SIL TERM SLDR RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-10J-10S(74) | 功能描述:环形推拉式连接器 JACK 10P FEM SLD GLD RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-10J-10SC | 功能描述:CONN HR10A JACK 10POS FEMALE RoHS:否 类别:连接器，互连式 >> 圆形 - 外壳 系列:HR10A 标准包装:1 系列:军用, MIL-DTL-38999 系列 III, ACT 连接器类型:母触点插座 位置数:5 外壳尺寸 - 插件:15-5 外壳尺寸，MIL:D 触点类型：:压接 触点尺寸:16 安装类型:面板安装，隔墙式（前端螺母） 紧固型:有螺纹 方向:N（正常型） 外壳材料，表面处理:合成物，草绿色镉镀层 防护等级:抗环境影响 特点:屏蔽 包装:散装 请注意:不提供触点 其它名称:DD38999/24JD5BN |
| HR10A-10J-10SC(73) | 功能描述:环形推拉式连接器 HR10A JACK 10POS FEM RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。