- 您现在的位置：买卖IC网 > PDF目录43683 > HR10A-10WTR-12S(73) 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE PDF资料下载
参数资料
| 型号： | HR10A-10WTR-12S(73) |
| 元件分类： | 圆形连接器 |
| 英文描述： | 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE |
| 文件页数： | 3/20页 |
| 文件大小： | 2215K |
| 代理商： | HR10A-10WTR-12S(73) |
189
HR10 Series●Push-Pull Connectors
■
Cable connecting methods
HR10B-2.5CP
HR10B-2.5CJ
1.Cable end treatment
Fig.1
1.Dimensions for cable end treatment are shown in
Fig 1.
2.Termination is described below.
(1).Strip cable outer jacket as indicated.
(2).Slit outer jacket on both sides per Fig.1.
(3).Fold back outer cover.
(4).Remove insulator from cable.
2.Soldering male pin to cable center
conductor.
Fig.2
1.Solder male pin to cable center conductor as
indicated in Fig.2.
(1).Pre-solder the solder pot of pin with 0.5mm
string solder.
(2).Male pin should fit flush against the cable
insulator as shown.
(3).Remove any excess solder from the pin with a
knife.This surface must be smooth.
(4).A properly soldered terminal will yield 500gf
when stretched.
3.Crimping cable outer conductor
Fig.3
1.Insert cable prepared per PROCESS 2 into the
connector.The cable should be inserted until it
comes to a full stop.This may be verified by
checking the dimension from the side of the
connector to the top of the contact(as indicated in
Fig 3). This dimension should be A.
2.Crimp this installed metal clamp with tool HR10-
TC-01 per Fig.3 and remove excess insulation with
a knife.
It is possible to pull back the contact.
Hold cable when crimping metal clamp and keep
the dimension to show in Fig 3. after crimping metal
clamp.
11±0.5
1.4±0.2
3.7±0.2
(2.5)
Slit cable outer jaket
2 pieces (180° reverse side)
Malu pin or Female pin
Soldering
Should fix flush
Contact fixing jig
such as vise
Clamp metal
(HR10B-2.5CP)
A
Connector
Remove excess insulator
material (remaining after
clamping is complated)
with a knife or aimilarobject.
Table 1 dimenshion A
2.5CP
2.5CJ
1.5±0.2mm
0
mm
+0.3
0
相关PDF资料 |
PDF描述 |
|---|---|
| HR10A-10WTR-12SB(73) | 12 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, SOLDER, RECEPTACLE |
| HR10A-13J-20PC(73) | 20 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, CRIMP, JACK |
| HR10A-13J-20SC(73) | 20 CONTACT(S), ZINC ALLOY AND BRASS, FEMALE, CIRCULAR CONNECTOR, CRIMP, JACK |
| HR10A-13P-20P(73) | 20 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, SOLDER, PLUG |
| HR10A-13P-20PC(73) | 20 CONTACT(S), ZINC ALLOY AND BRASS, MALE, CIRCULAR CONNECTOR, CRIMP, PLUG |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HR10A-10WTR-12SB | 功能描述:CONN RECEPT 12POS FEMALE DIP RoHS:否 类别:连接器，互连式 >> 圆形 系列:HR10A 产品目录绘图:63000 Series 63000 Series Front 63000 Series Side 63000 Series Cable End 63000 Series Assembly In Line 6P Mating Face 标准包装:500 系列:63000 连接器类型:插孔，母插口 位置数:6 外壳尺寸 - 插件:迷你型 DIN 外壳尺寸，MIL:- 安装类型:自由悬挂 端子:焊接 紧固型:推挽式 方向:带标记 防护等级:- 外壳材料，表面处理:青铜，镀镍 触点表面涂层:- 特点:- 包装:散装 触点涂层厚度:- 额定电流:- 电压 - 额定:- 工作温度:-40°C ~ 85°C 其它名称:275-1037 |
| HR10A-10WTR-12SB(73) | 功能描述:环形推拉式连接器 REC 12POS FEM DIP RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-10WTRB-12SB(01) | 制造商:Hirose 功能描述:CONN RECEPT 12POS FMALE PCB GOLD |
| HR10A-13J-20PC | 功能描述:CONN HR10A JACK 20 POS MALE RoHS:否 类别:连接器，互连式 >> 圆形 - 外壳 系列:HR10A 标准包装:1 系列:军用, MIL-DTL-38999 系列 III, ACT 连接器类型:母触点插座 位置数:5 外壳尺寸 - 插件:15-5 外壳尺寸，MIL:D 触点类型：:压接 触点尺寸:16 安装类型:面板安装，隔墙式（前端螺母） 紧固型:有螺纹 方向:N（正常型） 外壳材料，表面处理:合成物，草绿色镉镀层 防护等级:抗环境影响 特点:屏蔽 包装:散装 请注意:不提供触点 其它名称:DD38999/24JD5BN |
| HR10A-13J-20PC(73) | 功能描述:环形推拉式连接器 HR10A JACK 20 P MALE RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。