参数资料
| 型号： | HR10A-7P-6PC |
| 厂商： | Hirose Electric Co Ltd |
| 文件页数： | 18/20页 |
| 文件大小： | 0K |
| 描述： | CONN HR10A PLUG 6POS MALE |
| 标准包装： | 20 |
| 系列： | HR10A |
| 连接器类型： | 公触点插头 |
| 位置数： | 6 |
| 外壳尺寸 - 插件： | 7 |
| 触点类型：： | 压接 |
| 安装类型： | 自由悬挂 |
| 紧固型： | 推挽式 |
| 方向： | 带标记 |
| 外壳材料，表面处理： | 黄铜和锌，镀镍 |
| 包装： | 散装 |
| 请注意： | 不提供触点 |
| 其它名称： | *HR10A-7P-6PC HR161 |
The product information in this catalog is for reference only. Please request the Engineering Drawing for the most current and accurate design information.
HR10 Series ● Push-Pull Connectors
■ Connection work procedure(plug side)
This applies also to the jack side connection work.
No special connection work procedure is given here for the receptacle side because no special procedure is
necessary.
P shell unit
Plug body
Clamp washer
Tightener
Cable
Bifurcated part
About 2
C
Face A
Face B
Spanner jaw distance
P shell unit
Clamp
Plug body
Spanner jaw distance
Cord bushing
Cable
A
2 or more
2 -0.5 for crimp type
About 2 for solder type
0
D
Boss
Set screw
Table 2 spanner jaw distance
Table 3 cable end processing dimensions
Table 1
Size
Size 7
HR10
8
HR10A
7.5
Size
Dimension C Dimension D for HR10A
for HR10 Solder type Crimp type
Size
Size 7
Tightening force
1.5N?m(15kg?cm)
Size 10
Size 13
11
––
9.5
13
Size 7
Size 10
5.5 or less
7 or less
10
16
15-20
15-20
Size 10
Size 13
2N?m(20kg?cm)
2N?m(20kg?cm)
HR10 TYPE
Size 13
––
26
26
HR10A TYPE
Use cables with a nominal sectional area of 0.129 mm (AWG#26) at the finish outside diameters applicable for each size.
1
2
After processing the cable ends according to the dimensions in the abo ve drawings, fit the parts to the cable as shown in the drawings.
2
3
Fit the parts to the cable in the following order: tightener, clamp
washer, and plug body.
(solder type)
Insert the P shell unit into the assembly tool stand and solder it.
(crimp type)
Fit the parts to the cable in the following order: cord bushing and
plug body.
After crimping the appropriate crimp terminal to the cable core, insert t he crimp terminal into the terminal hole in the P shell unit.
Assemble the connector in the following steps.
1. Screw the plug body into the thread in the P shell unit with the
tightening force shown in Table 1 using a torque wrench with a
fixed torque.
Before tightening the plug body,slacken part C so that no load is
1. Fix by caulking the clamp accompanying the cable with the cable
crimping tool(HR10A-TC-02)
2. Screw the plug body into the thread in the P shell until with a
tightening force shown in Table 1 using a torque wrench with a
4
5
applied to the soldered wires.
2. Apply the clamp washer to the bifurcated part of the plug body,
and then tighten the tightener until surface B touches the plug
body surface A.
This completes the work.
fixed torque. Before tightening the plug body, slacken the part D so
that no load is applied to the soldered wires.
3. Tighten the set screw so that the tip of the screw presses one of
the two bosses on the clamp.
Fix the set screw with a tightening torque of 0.3N(3kg?cm)
4.Attach the cord bushing to the plug body.
For any question on using the plugs, contact our sales or engineering department.
Remarks : Loctite 242, Henkel Japan or equivalent is recommend to prevent the male thread section of the P shell unit and the set screw
for loosing.
196
相关PDF资料 |
PDF描述 |
|---|---|
| OSTHW155051 | TERMINAL BLOCK PLUG 5.08MM 15POS |
| HR10A-7P-4PC | CONN HR10A PLUG 4POS MALE |
| HR10A-13R-20PC | CONN HR10A RECEPT 20POS MALE |
| HR10A-10R-12SC | CONN HR10A RECEPT 12POS FEMALE |
| HR10A-10J-12SC | CONN HR10A JACK 12POS FEMALE |
相关代理商/技术参数 |
参数描述 |
|---|---|
| HR10A-7P-6PC(73) | 功能描述:环形推拉式连接器 6P PLUG SHELL SZ 7 MALE CRIMP RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-7P-6S | 功能描述:6 CONTACT PLUG W/SOCKET INSERT RoHS:否 类别:连接器，互连式 >> 圆形 系列:HR10A 标准包装:1 系列:军用, MIL-DTL-5015, MS 连接器类型:插座，公形引脚 位置数:2 外壳尺寸 - 插件:22-11 外壳尺寸，MIL:- 安装类型:自由悬挂 端子:焊杯 紧固型:有螺纹 方向:N（正常型） 防护等级:抗环境影响 外壳材料，表面处理:铝，镀草绿色镉 触点表面涂层:银 特点:应力消除 包装:散装 触点涂层厚度:- 额定电流:- 电压 - 额定:1750VAC，2450VDC 工作温度:-55°C ~ 125°C 配套产品:IMS3108R22-11S-ND - CONN PLUG 2 POS RT ANG W/SCKTIMS3106F22-11S-ND - CONN PLUG 2 POS STRAIGHT W/SCKTIMS3106E22-11S-ND - CONN PLUG 2 POS STRAIGHT W/SCKTIMS3106R22-11S-ND - CONN PLUG 2 POS STRAIGHT W/SCKTIMS2518322-11S-ND - CONN PLUG 2 POS STRAIGHT W/SCKT 其它名称:IMS3101E22-11P |
| HR10A-7P-6S(01) | 制造商:Hirose 功能描述:CONN PLUG 6POS FEMALE SLD GOLD |
| HR10A-7P-6S(73) | 功能描述:环形推拉式连接器 6P PLUG SHELL SZ 7 FEMALE SIL TERM SLDR RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
| HR10A-7P-6S(74) | 功能描述:环形推拉式连接器 PLUG 6P FEM SLD GOLD RoHS:否 制造商:Hirose Connector 产品类型:Connectors 系列:HR10 触点类型:Socket (Female) 外壳类型:Receptacle 触点数量:4 外壳大小:7 安装风格:Panel 端接类型:Solder 电流额定值:2 A |
发布紧急采购，3分钟左右您将得到回复。